From the given input signal we can find the time period 't'
t=0.07-0.03=0.04
Now the frequency =1/t
f=1/(0.04)=25hz
X0=1.5
X1=1.5
X-1=1.5
*** Please give me likes ***
PROBLEM: A signal x(t)-A cos (2nfit + ф) įs shown in the figure bclow. x (t)...
No mathematical expression for x(t). Problem 2: A message signal x(t), is illustrated in the graphs below x(t) 1.5 1 0.5 -1 3 -0.5 1 -1.5 Time (s) 2 1 -45 -30 -15 0 15 Frequency (kHz) This signal is applied to a Narrow Band FM generator as shown below; x(t) Ф. (t) NBFM 5.60 MHz. anda frequency deviation The NBFM Signal p(t) has a center frequency f Afi 2.4 kHz - A. Sketch the time-domain signal p1(t) using the...
Q1) Given an analog signal X(t) = 3 cos (2π . 2000t) + 2 cos (2π . 5500t) sampled at a rate of 10,000 Hz, a. Sketch the spectrum of the sampled signal up to 20 kHz; b. Sketch the recovered analog signal spectrum if an ideal lowpass filter with a cutoff frequency of 4 kHz is used to filter the sampled signal in order to recover the original signal ; c. Determine the frequency/frequencies of aliasing noise . Q2)...
Problem 1 Consider the sinusoidal signal x(t) shown below. 10 8 4 2 4 6 8 -10 0.2 0.4 0.6 0.8 t (seconds) (i) What is the amplitude of this signal? ii) What is the period of this signal (in seconds)? (iii) What is the frequency of this signal (in Hertz)? (iv) Write an equation for this signal.
Digital Signal Processing DFT Consider a speech signal x() that has the following frequency spectrum: xga) 1 + cos( -/100 a) Select appropriate values of N and T that will help us carry out DFT-based spectral analysis of this signal x401@) 800 such that the continuous-time frequencies are sampled no farther than 10 Hz apart. b) Ignore the issue of spectral leakage; under this assumption, provide a closed-form expression for the DFT of the signal using the values selected in...
Problem 2) For a 2 DOF system the equations of motion are given as: [mi 0 0 m2 (X2 mig L -m29 L -m29 L m29 L Where m1 =m2 =m g=gravity and L =length a) Determine the frequencies and mode shapes. b) Verify that the natural modes are orthogonal. c) Determine the response fX:(0) Note: x1(t) = xo , x2(t) = 0 and xi(t) = xo , iz(t) = 0 d) If the system is excited by a harmonic...
Signal xo(t) 5 cos (200π1+ 품 ) + 4 sin (300π) is sampled at a rate of Fs = 1 kHz to obtain the discrete-time signal x[n]. (a) Determine the spectrum X(ej ) of x[n] and plot its magnitude as a function of ω rad sam in tad and as a function of F in Hz. Explain whether the original signal xe(t) can be recovered from xln]. (b) Repeat part (a) for 500 Hz. (c) Repeat part (a) for 100...
Problem 1. Equipment ratings and per-unit reactances for the system shown in figure 1. are given as follows Using a 100-MVA, 230-kV base for the transmission lines, draw the per-unit sequence networks Consider the impact of ?-Y phase shifts Synchronous generators: G 100 MVA 25kV X1-X2 0.2Xo 0.05 G2100 MVA 13.8 kV X,-X2 0.2 Xo 0.05 Transformers: TI 100 MVA 25/230 kV Xi-X-Xo-0.05 T2 100 MVA 13.8/230 kV X-X2 = Xo 0.05 Transmission lines: TL 12 100MVA 230 kV X,=X2=0.1...
Problem 1 A sinusodial signal x(t)- sin2t (t in seconds) is input to a system with frequency response: H(G What signal y(t) is observed at the output? Problem 2 The inverse Fourier transform of a system frequency response is given by h(t)t. The signal x(t) 3 cos(4t 0.5) is input to the system (t in seconds). (a) What is the expression of the signal y(t) at the system output? (b) What is the power attenuation in dB caused by the...
please help as soon as possible 1. Consider the system shown in Figure 1 below. Ideal Ideal y(t) Sample period T Sample period T Figure 1. System for Problem 1. The input to the above system is x(), the output is y), and the sampling period for both the ideal A/D and ideal D/A is T>0. For your answers to the various parts below, be sure to include appropriate units, where applicable. a) Suppose that x(t)-5. Determine all numerical values...
1. Consider the system shown in Figure 1 below. Ideal Ideal r(t) Sample period Sample period T Figure 1. System for Problem 1. The input to the above system is x(), the output is y(), and the sampling period for both the ideal A/D and ideal D/A is T>0. For your answers to the various pa be sure to include appropriate units, where applicable. rts below., Suppose that x(1) Justify your answer. a) 5. Determine all numerical values of T...