7. In the rectangle ABCD shown in the figure, M, is the midpoint of DC, M2...
Problem 2. [25 pts) Side AB of the square ABCD is extended to P, A - B - P, so that BP 2 AB. With M the midpoint of DC, BM is drawn meeting AC at Q. PQ meets BC at R. Using Menelaus' theorem find the ratio R. P C M Problem 2. [25 pts) Side AB of the square ABCD is extended to P, A - B - P, so that BP 2 AB. With M the midpoint...
A four-particle system is shown in the figure below, and the masses of the particles are ni l1 m1 3.4 kg m2 3.5 kg m3 3.4 kg m4 3.5 kg 2.0 m 2.0 m 12 (a) Find the moment of inertia Ix about the x axis, which passes through m2 and m3 kg m2 (b) Find the moment of inertia ly about the y axis, which passes through m1 and m2 kg m2
52% A cyclic quadrilateral is shown. Not drawn accurately x + 10° X: y = 3:7 у Work out the size of angle z. + z х n с ABCD is a parallelogram where AB = m and BĆ = n В, F is the midpoint of the line BD. a) Express FD in terms of m and n. FD = Van - Vam m; A D E is the point such that ADE is a straight line with AD:...
a simply supported beam abcd with arectangular cross section carries the loading shown in figure. the uniform beam has a mass of 33 kg per meter (m kg/m) and a cross section as shown in the figure. you may take 10 m/s^2 as acceleration.Question A2 A simply supported beam ABCD with a rectangular cross-section carries the loading shown in Figure QA2. The uniform beam has a mass of m kg per meter of length (m kg/m) and a cross-section as shown...
As shown in (Figure 1), five balls (masses m1 = 2.20kg, m2 = 2.15kg, m3 = 2.11 kg , m4 = 2.05 kg , m5 = 2.00kg) hang from a crossbar. Each mass is supported by "5-lb test" fishing line which will break when its tension force exceeds 22.2 N ( = 5.00 lb). When this device is placed in an elevator, which accelerates upward, only the lines attached to the 2.05 kg and 2.00kg masses do not break. Within...
3. In the circuit shown below, the differential pair (Mand M2) is biased with a current miror that consists of M3, M and Rref. The circuit parameters are: VDD-3 V, Rre/-15 ka, RD = 20 ka, and RL-40 kn. The transistors 25 M, and M, are identicalwith()M and M, are identical with (The oh M and M4 are identical with = ·The other transistor parameters are: indox-: 0.1 m1A/V2,VTN-0.5 V, γ-0 (body effect coefficient) and λ 0 (channel length modulation...
Provide detailed solution with assumptions. Rainwater flows through the galvanised iron downspout shown in Figure 4 at a rate of 0.006 m3/s. The downspout cross-section is a rectangle with aspect ratio 1.7:1 and is is completely filled with water. The velocity of the water in the gutter at the free surface and head loss associated with the bend can be neglected. Q4. a) Determine the hydraulic diameter of the cross section, in terms of the 2 marks] [2 marks] [3...
gen1 5). 8 pts. M and M2 are fixed in free space as shown. Where between M and M2 can we place a test mass (M3 ) so that the resultant force on it will be zero? ie x = ? • finish the sketch M - 32 kg M2 - 2 kg 8 m
In a steam power cycle shown in the figure, the pressure of the water vapor exiting from the boiler with 1 kg mass at 1 point is P1 = 4 MPa, while the temperature is T1 = 400 oC, the pressures at the inlet and outlet of the mixing chamber (K.O.) are P2 = P3 = P4 = 1 MPa. The temperature at the inlet of the low pressure turbine (A.B.T.) is measured as T4 = 240 oC and the...
QUESTION3 As shown in Figure Q3, a cantilever beam ABCD is used to support uniform load 4 KN/m along span BC and momvent at point A. U'sing Macaulay's method, L express the deflection of the beam stiffness in terms of E 6 marks) ii. determine the deflection at point C, and (2 marks) ili. calculate the slope at end A (2 marks) 3 kNm Figure QWRajah S3 QUESTION3 As shown in Figure Q3, a cantilever beam ABCD is used to...