1. Design R1, R2, Rs, Ro to give los-1mA with Voo 12 V2: Use a 2V...
Please answer clearly Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a) Voltage gain (Vo/vi) b) Input resistance (R) c) Output resistance (Ro) d) Maximum output voltage swing so as the amplifier stays in saturation mode. Assume VDD-20 V, R1-2.5 ΚΩ, R2-1KQ, R3-0.5 ΚΩ, R4-5 MQ, R5_1ΜΩ. R4 R1 R5 R2 Ro R3 Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a)...
3. Consider the following multistage amplifier. The current source values are 1, -2mA, I, - 1mA, and 1 - 1mA. Also, Voo - Vss - 6V. +VDD (a) If the DC voltage at the output is OV, find all DC currents at the drains of all transistors. Also, find the DC voltages at the drain, gate, and source terminals for all transistors (you can put the values directly on the figure). Use k.(W/L) - k.(W/L) = 2mA/V. And Vin -...
4) find 11, 12, 13, V2, and V3 {R1 V2 {R2 V1:6 R1 : 300 2 R2: 1.7 KS2 Ans 1 5) calculate the unknown resistance Rx, when V, the voltage across the bridge is 0 in the below Wheatstone bridge RI: 100 2 R2: 4002 R3 : 250 2 Ans Rx 6) write down in detail what was your contribution in the Physics experiment show me one of the experiments you did in the lab
4. The MOSFET in the circuit given below has Vi- 1 V, kn 0.8 mA/V2, and VA 40 V a) Find the values of Rs, Ro, and Ro so that Io -0.1 mA, the largest possible value for RD is used while a maximum signal swing at the drain of tl V is possible, and the input resistance at the gate is 10 MS2. b) Find the values of gm and ro at the bias point c) If terminal Z...
Vw Vout V2 SR, The circuit above has R1 = 1.5 k22, R2 = 2 k22, R3 = 1 k2, R4 = 2 ks, R6 = 2 k2, R2 = 750 12, Rg = 4 k22 and Rg = 1 k12. If V2 = 3 V + 3 sin(2000nt) V, determine R5 and the dc voltage v1 so that the output is 5.4 sin(2000nt) V. O v1 = -0.5 Vdc and R5 = 1 k12 Ov1 = 0.7 Vdc and...
This is a very important assignment of mine please do it correctly I will give you thumbs up Problem 1. The transistor in the circuit shown to the right has parameters VTN = 0.4 V, Kn = = 0.5 mA / V2, and λ = 0. The circuit parameters are VDD = 3 V and Ri = R1||R2 = 300 kΩ. a)Determine the values of R1, R2, and RS such that IDQ = 0.25 mA and VDSQ = 1.5 V....
C.la For the circuit of Figure 1, choose values for resistors R1, R2, and R3(all resistances must be greater than one Kilo ohm). Given that the voltage source Vs1 = 8V and Vs2 = 10V determine the output voltage Vout. C.1b For the same resistor values Ri, R2, and Rs you chose in part C.la Given that the voltage source Vsi = 8V and Vs2 = 10V, use Figure 2(a) to determine the output voltage Vout/ and Figure 2(b) to determine the output voltage Vout2. Discussion:...
R1 Vin {R2 13|VRS R4 ob Configure the circuit above in Autodesk Circuits in TinkerCAD. Use a breadboard and any relevant components/equipment. The parameters for the components in the circuit are: DC supply voltage of 12V, R1 = 3309, R2 = 4700, R3 = 100n and R4 = 2200 a) Measure the voltage across resistor R3 using a multimeter and give the measured voltage b) Measure the current through resistor R3 using a multimeter and give the measured current mA...
R1-20 R2 30 1) In Fig. 6, V2 will be: a) 0.7v b) 1.5v c) 2.4v d) 5.0v e) 6.0v RS Fig. 6 2In Fig. 6, what minimum size (wattage) resistor should be used for R a) 1/8 b) 1/4 c) 1/2 d) 1W 2 w
can someone help me with part c mpt tope alswersol the sdme part of you willbe penalized for this. Question 1 1 pts For the circuit shown in Figure 6.49, let Vcc -9V.RE 0.11 kQ, R1 3.6 k2, R2 5.6k(2, and Rs -o Ω . The transistor parameters are β-200. VBE(On)-Q7V, VA - 100 V and VT 0.026 V.(a) Determine the quiescent value of lEQ. (b) Find the small-signal voltage gain Av-vo/vg (c) Determine the output resistance Ro looking into...