Use measured resistance values and node analysis to calculate the node voltages. Use measured resistance values...
i dont undersrand how to calculate the values from measured data? 2. Turn on the DC power supply, measure its output voltage with DMM2 and record it as measured data Vs in Table 6. 3. Use DMM2 to measure the voltages V, V2.V. Va across R R. RR respectively. Use DMMI to measure the current Is (notice: Is=1= 12 + 1,-1). Record the measured values of I, and V., V2, V3. V4 in Table 6. 4. Turn off the DC...
1. calculate node voltage V1 and V2 2. calculate the voltage drop across 10k resistor equal to the difference between V2 and Vs2 3. Calculate mesh current i1,i2, i3 4. calculate the current through 2.7k resistor 5. does the current measured through 2.7k resistor equal to the difference between the currents i2 and i3? show all calculations equired Itheory a Construct the circuit shown in Fig. 2 on your breadboard. 1 k 2 w V, 1k22 V, 10 k92 VS2...
Name: ENGT 3050 Fundamentals of Electricity LAB EXERCISE #3 Series and Parallel Circuits Objectives: The objective of this exercise is to examine Kirchhoff's Voltage and Current Laws. Kirchhoff's Voltage Law (KVL) states, for a closed loop series path the algebraic sum of all the voltages around any closed loop in a circuit is equal to zero. Kirchhoff's Current Law (KCL) states, for a parallel path the total current entering a circuits junction is exactly equal to the total current leaving...
Laboratory Measurements Make the circuit 2.1. Measure the voltages and currents and record the measured values in Table 2.1. Make the circuit 2.2. Measure the voltages and currents and record the measured values in Table 2.2. Make the circuit 2.3. Measure the voltages and currents and record the measured values in Table 2.3 Circuit 2.1 R1 A R3 1.2kohm 2.2kohm V2 R2 18V 3.3kohm Fig. 2.1 I2- IR3 Table 2.1VRi Calculated (coded) Measured 1- LR1 IR2 Circuit 2.2 R1 R3...
1) (10 marks) In this question, you will calculate the voltages, currents and powers as follows for the dc circuit in Fig. 1. a) Using mesh analysis, calculate the mesh currents. Redraw the circuit with the mesh currents added. b) If the bottom node of the 3 12 resistor is 0 V, what is the voltage at the top node of the 312 resistor? c) Calculate the power that is absorbed or produced by each of the circuit elements. For...
Find the node voltages v1, v, and v2. Use nodal analysis. R3 R 2 17 3 1 2 Given Variables: R1:2 ohm R2 1 ohm R3 1 ohm R4 2 ohm Vs:5 V Is : 1 A
Consider the network of Fig Pl.1. (a) 1. Label all node voltages and branch (b) Use the principle of superposition to (c) Determine the voltages v, V2, and v;3 i, l 80 Ω 50cos2000t V currents. 100 Ω 40 mHv, compute the currents io, il, i2, i3, and 4. + 24 v (d) Determine the power from the three S602 sources in the circuit Consider the network of Fig Pl.1. (a) 1. Label all node voltages and branch (b) Use...
1. (12 marks) For the circuit in Fig. 1: a) Label all the node voltages and show and label all branch currents for mesh analysis if they are not already labelled. (2 marks) b) Calculate the currents using mesh analysis. Show your equations and solutions in a logical order. (6 marks) c) Calculate the power generated or absorbed by each element including the sources. Show that power is conserved in the circuit. (4 marks) 10 12 212 512 1 341...
1. Use PSpice to find the node voltages for the following circuit. 2% 12 4Ω ΙΩ 4Ω 10 V I A 2. Use PSpice to find the mesh currents for the following circuit. 8Ω 3 A 12 V 40(із 2u
Problem One (25 points) 300A. Determine the equivalent resistance as seen by the current source is in the circuit shown below. Show carefully each step of your solution process. B. Find the magnitude of the power delivered by the source in the circuit shown if current source is = 50 mA. OSA 100 150 12 w 75or SOL 5000 750 n 1kn 36000 250 12 3002 Velg Problem Two (25 points) v=l6 Consider the electrical circuit shown below. Suppose that...