a) [3 pts.] Design and draw a voltage divider that produces an output voltage of 14.4...
Design and draw a voltage divider that provides an oupit of 15V with no load attached, using as many 9-V batteries, 100 ohm resistors, and 50 ohm resistors as you'd like
Q1. You are given a 12 V DC power supply. You are expected to develop a voltage divider to achieve a voltage of nominal 5V value using a pair of resistors from the E 12 range, with the restrition that you are not expected to draw a current of more than 1 mA from the 12 V DC supply i. Develop a simple circuit showing the possible values for each resistor pair, and the range of the DC output possible...
Problem 1130 pts 1. [12 pts] For the circuit shown in Fig. 1, istance Rm when the switch is open. What type of voltage gain Vo/Vin and the input resistance Rin when the switch is close. What type of a) Find the voltage gain val vin and the input resistance Rin when the switch is open b) Find the amplifier is this? amplifier is this? tin vo R Fig. 1 [18 pts] Design a circuit that implements the following: Vo(t)...
a9a resistive load. Inductor 3-(35 pts) Design a converter that has an input voltage of 24 V DC and supplies 18 V DC to current is desired to be continuous and must not change more than 30 % of its average value voltage ripple must be lower than 2 %. Switching frequency is 10 kHz. a) Draw the circuit diagram. Calculate the duty ratio. Calculate values for 2 desired conditions of the inductor current and determine the value of the...
Consider the bridge circuit in Figure. 1. (3 pts.) Find the output voltage “Voi” as a function of the variation value “S”. ZR(1+0) 2. It is required to design an instrumentation amplifier such that the M + V01 - output varies between +3V and -3V as the parameter varies between +0.025 and -0.025. (2Pts) Sketch the circuit of the instrumentation amplifier, V connected with the bridge-output. • (5pts) Design the amplifier with the following parameters. © Each bridge-resistance R= 50...
Problem 3: 10 pts. Calculate the power supplied by a voltage source with an output voltage of V 10V sin(ot). Measurement of the current into the load indicates that I 10mA cos(ot). a) Calculate the instantaneous power. Sketch the function. (6 pts) b) Find an expression for the average power and calculate the average power for the voltage and current waveforms. (4 pts)
Exercise #4 Voltage Divider A. Introduction In a previous exercise, you learned about the current-voltage relationship in a single resistor. Now, you will about how voltage is divided across two resistors in series. In this exercise you will: Examine the operation of the electric circuit known as the voltape divicder At the conclusion of this exercise you should be able to Compute the valtage across a resistor in a voltage divider circuit Design a voltage divider circuit to produce a...
6.108 (d) Section 6.5: Discrete-Circuit Amplifiers 6.107 Calculate overall voltage gain G, of a 3 mA/V, ro= = 10 MS2. The amplifier is the common-source amplifier for which g 100 k2, RD 10 k2, and RG fed from a signal source with a Thevenin resistance of l M2, and the amplifier output is coupled of 20 k2 to a load resistance SIM 6.108 The NMOS transistor in the CS amplifier shown in Fig. P6.108 has V, = 0.7 V and...
D Question 2 10 pts A three phase full-bridge rectifier draws 12-kW from a power supply that has 150-V phase-to-phase voltage. The power factor is 0.77. What is the maximum (peak) value of the current delivered by the supply? 10 pts DI Question 3 A full bridge, square wave inverter supplies an RL load with R-7-Ohm and L-58-mH. The DC voltage is 90-V and the output waveform frequency is 60-Hz. What is the magnitude of the third harmonic of the...
Please design a clipper circuit that produces voltage as shown. You may the standard value pf resistor as guidlines ASSIGNMENT BEE2213 19201 QUESTION 2 Design a clipper circuit that produces voltage output as shown in the Figure 1. Vi 15V N ? Vi Vo Vo 5V Figure 1 @ 43% .. MY MAXIS 4G 14:38 Done Assignment_Guideline_2130afeo... 2 RSG FREE BEE2213/192011 APPENDIX 1- Standard Value Resistors Standard Values of Commercially Available Resistors Ohms (0) Kilo Ohms (KO) Mega Ohms (MO)...