Homework Answers
Add Answer to:
D Question 2 10 pts A three phase full-bridge rectifier draws 12-kW from a power supply that has 150-V phase-to-phase voltage. The power factor is 0.77. What is the maximum (peak) value of the cur...
Power electronics question 2) Consider that you have a single-phase H-Bridge inverter Using this triangle waveform...
Power electronics question
2) Consider that you have a single-phase H-Bridge inverter Using this triangle waveform as your guide, sketch the output voltage of a single phase H-bridge inverter with an input voltage of 200 V dc and an output voltage with the following characteristics: - Peak voltage = 170 V - Frequency=1/15 that of the triangle Indicate in the figures all important values. Assume that there is not filter at the inverter output. Relative Amplitude Amplitude
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliv...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
1. A full-bridge three-phase SCR rectifier supplies an L-R load from a 208 V line-to-line 60...
1. A full-bridge three-phase SCR rectifier supplies an L-R load from a 208 V line-to-line 60 Hz source. The load draws 25 kW when the SCR phase delay angle is 60°. What is the pulse number for this rectifier circuit? Plot the load power as a function of delay angle for 0° < α 75°
QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates f...
QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates from the mains and provides an output of Voc-20 V with 20% ripple, when the load current is 2 A Calculate the maximum and minimum values of the output waveform of this power supply. b. Now you will design a series voltage regulator between the power supply described in part (a) and an electronic device operating at 12 VDC...
Capacitor is connected to secondary (1) A fullwave bridge rectifier power supply is powered from the secondary of a transformer which has a peak secondary voltage of 22V. The primary of the transforme...
Capacitor
is connected to secondary
(1) A fullwave bridge rectifier power supply is powered from the secondary of a transformer which has a peak secondary voltage of 22V. The primary of the transformer is connected to a 50Hz, 230Vus power supply. A 2700μF filter capacitor is used. A current of 1.5 Amp is drawn from the supply (i) Sketch a schematic diagram of the setup (ii) Calculate the mean dc output voltage (ii) Assume that each diode conducts for one-twelfth...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a transformer which has a rms secondary voltage of 15.6V. The primary of the transformer is connected to a 50Hz, 230VRMS power supply. A 2700uF filter capacitor is used. A current of 1.5 Amp is drawn from the supply. (i) Sketch a schematic diagram of the setup. (ii) Calculate the mean de output voltage. Assume each power diode has a forward voltage drop of 1...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
Question 1 (25 marks) a) A full wave rectifier has 40V peak secondary voltage, 2,000uF capacitor...
Question 1 (25 marks) a) A full wave rectifier has 40V peak secondary voltage, 2,000uF capacitor and 1022 load. You may take the line frequency as 50Hz and voltage drop across a diode as 0.7V. i. Calculate the peak dc voltage (VA). (2 marks) ii. Calculate the dc load voltage (Vdcloed). (4 marks) iii. Calculate the ripple voltage (AVLoad). (4 marks) b) The capacitance, inductance and load resistance of a Buck step-down dc-to-dc converter are 1.0uF, 10uH and 20.022 respectively....
2. Figure 2 shows a 6-pulse thyristor rectifier feeding a DC static load an operating at steady-state. The ac input power supply is a symmetric set of three-phase voltages forming a direct seque...
2. Figure 2 shows a 6-pulse thyristor rectifier feeding a DC static load an operating at steady-state. The ac input power supply is a symmetric set of three-phase voltages forming a direct sequence, having rms line-to-line voltage of Vuns equal to 415 V and angular frequency ω equal to 100π rad/s. The load is sufficiently inductive to smooth out the load current i(t), i.e. i 1, where I is a constant. a. Derive the mathematical expression of the average DC...
4.6. A 460-V, 75 kW, 4-pole, delta-connected, 60-Hz, three- phase induction motor has a full-load slip of 5 percent, an efficiency of 92 percent and a power-factor of 0.87 lagging at full-load. At st...
4.6. A 460-V, 75 kW, 4-pole, delta-connected, 60-Hz, three- phase induction motor has a full-load slip of 5 percent, an efficiency of 92 percent and a power-factor of 0.87 lagging at full-load. At start-up, the motor develops 1.9 times the full load developed torque but draws 7.5 times the rated current at the rated voltage. This motor is to be started with an auto- transformer reduced-voltage starter. Assume the stator resistance and the stator core loss to be negligible. Calculate...
Power electronics question
2) Consider that you have a single-phase H-Bridge inverter Using this triangle waveform as your guide, sketch the output voltage of a single phase H-bridge inverter with an input voltage of 200 V dc and an output voltage with the following characteristics: - Peak voltage = 170 V - Frequency=1/15 that of the triangle Indicate in the figures all important values. Assume that there is not filter at the inverter output. Relative Amplitude Amplitude
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
1. A full-bridge three-phase SCR rectifier supplies an L-R load from a 208 V line-to-line 60 Hz source. The load draws 25 kW when the SCR phase delay angle is 60°. What is the pulse number for this rectifier circuit? Plot the load power as a function of delay angle for 0° < α 75°
QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates from the mains and provides an output of Voc-20 V with 20% ripple, when the load current is 2 A Calculate the maximum and minimum values of the output waveform of this power supply. b. Now you will design a series voltage regulator between the power supply described in part (a) and an electronic device operating at 12 VDC...
Capacitor
is connected to secondary
(1) A fullwave bridge rectifier power supply is powered from the secondary of a transformer which has a peak secondary voltage of 22V. The primary of the transformer is connected to a 50Hz, 230Vus power supply. A 2700μF filter capacitor is used. A current of 1.5 Amp is drawn from the supply (i) Sketch a schematic diagram of the setup (ii) Calculate the mean dc output voltage (ii) Assume that each diode conducts for one-twelfth...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a transformer which has a rms secondary voltage of 15.6V. The primary of the transformer is connected to a 50Hz, 230VRMS power supply. A 2700uF filter capacitor is used. A current of 1.5 Amp is drawn from the supply. (i) Sketch a schematic diagram of the setup. (ii) Calculate the mean de output voltage. Assume each power diode has a forward voltage drop of 1...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
Question 1 (25 marks) a) A full wave rectifier has 40V peak secondary voltage, 2,000uF capacitor and 1022 load. You may take the line frequency as 50Hz and voltage drop across a diode as 0.7V. i. Calculate the peak dc voltage (VA). (2 marks) ii. Calculate the dc load voltage (Vdcloed). (4 marks) iii. Calculate the ripple voltage (AVLoad). (4 marks) b) The capacitance, inductance and load resistance of a Buck step-down dc-to-dc converter are 1.0uF, 10uH and 20.022 respectively....
2. Figure 2 shows a 6-pulse thyristor rectifier feeding a DC static load an operating at steady-state. The ac input power supply is a symmetric set of three-phase voltages forming a direct sequence, having rms line-to-line voltage of Vuns equal to 415 V and angular frequency ω equal to 100π rad/s. The load is sufficiently inductive to smooth out the load current i(t), i.e. i 1, where I is a constant. a. Derive the mathematical expression of the average DC...
4.6. A 460-V, 75 kW, 4-pole, delta-connected, 60-Hz, three- phase induction motor has a full-load slip of 5 percent, an efficiency of 92 percent and a power-factor of 0.87 lagging at full-load. At start-up, the motor develops 1.9 times the full load developed torque but draws 7.5 times the rated current at the rated voltage. This motor is to be started with an auto- transformer reduced-voltage starter. Assume the stator resistance and the stator core loss to be negligible. Calculate...
Most questions answered within 3 hours.
-
Which of the following pairs of ions have the same electron
configuration?
I: Br− and Se2−...
asked 1 hour ago -
The Foremost Composite Materials Company is planning a two-day
sales conference for October 19-20. The conference...
asked 1 hour ago -
3) Illustrate the observed pattern of relatedness of organisms
versus adaptations to specific conditions. This means...
asked 2 hours ago -
In winter a lake has a 0.35 m thick ice layer over 1.10 m of
water....
asked 2 hours ago -
Assuming the following has been encrypted with a Vigenere cipher
below, use the method(s) and assumptions...
asked 3 hours ago -
How would I use switch statements to write a program that will
take an input of...
asked 3 hours ago -
Imagine a reaction in which methane gas combusts at a constant
pressure of 1 atm and...
asked 3 hours ago -
Two parallel wires (each 12 m in length) are separated by a
distance of 0.065 m...
asked 3 hours ago -
Suppose there were three masses at the corner of uniform
equilateral triangle. The masses are m1...
asked 3 hours ago -
Situation: A building that is 618 m above the ground floor. How
many times would a...
asked 3 hours ago -
help me and discuss one successful and one
unsuccessful international company/busines in Indonesia.whyit
succeed and why...
asked 3 hours ago -
I- Choose the best answer
Which of the following statements about the structure and
packaging of...
asked 3 hours ago