Question

c A long cylindrical rod of diameter D1-0.01 m is coated with this new material and is placed in an evacuated long cylindrica
0 0
Add a comment Improve this question Transcribed image text
Know the answer?
Add Answer to:
c A long cylindrical rod of diameter D1-0.01 m is coated with this new material and...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • A long, cylindrical electrically heated rod, 2cm in diameter, and is installed in a vacuum furnace...

    A long, cylindrical electrically heated rod, 2cm in diameter, and is installed in a vacuum furnace The surface of the heating rod has an emissivity of 0.9 and is maintained at 1000 K, while the interior walls of furnace are black and are 800 K. Calculate the net rate at which heat is lost from the rod per unit length. lgnore the flux from the endpoints.

  • heat transfer Consider the picture shown below. The very long cylindrical rod (surface 1) acts as...

    heat transfer Consider the picture shown below. The very long cylindrical rod (surface 1) acts as a black surface 1 m in diameter which is maintained at 1000 K. The rod is surrounded by a very thin cylindrical shield with inner surface 3-1 and outer surface 3-2. The diameter of this shield is 2 m; and is so thin that the inner and outer surface areas are essentially the same. The shield has an emissivity of 0.3 on both sides....

  • A long cylindrical rod of diameter 220 mm with thermal conductivity 0.5 W/m-K expe riences uniform...

    A long cylindrical rod of diameter 220 mm with thermal conductivity 0.5 W/m-K expe riences uniform volumetric heat generation of 25,000 W/m3. The rod is encapsulated by a circular sleeve having 7 W/m K. The outer surface of the sleeve is exposed to cross flow of air at 25°C with a convection coefficient of 25 W/m2-K. Find the temperature at the interface between the rod and sleeve, and on the outer surface. an outer diameter of 410 mm and thermal...

  • The cylindrical surface of plastic cylinder, 20.0 m long and 2.80 cm in diameter is coated...

    The cylindrical surface of plastic cylinder, 20.0 m long and 2.80 cm in diameter is coated on the outside with a uniform layer of gold, 0.09 mm thick. A voltage source of 12 V is applied across the flat ends. ρgold = 2.44 × 10−8 Ω · m What is the resistance of the coated cylinder?

  • A long slender solid cylindrical rod made of copper is 2 cm in diameter. It is...

    A long slender solid cylindrical rod made of copper is 2 cm in diameter. It is taken out of a liquid nitrogen bath at 77 K and exposed to a stream of warm air at a temperature of 50 C. Neglect internal temperature gradients find the time taken by the rod to heat up to a temperature of 10 C if the surface heat transfer coefficient is 20 W/m^2K. For copper, take k=330 W/mK and ?=95*10^-6 m^2/s.

  • A very long rod of 5-mm diameter and uniform thermal conductivity k = 25 W/m-K is subjected to a heat treatment process

    A very long rod of 5-mm diameter and uniform thermal conductivity k = 25 W/m-K is subjected to a heat treatment process. The center, 30-mm-long portion of the rod within the induction heating coil experiences uniform volumetric heat generation of 7.5 x 106 W/m3. The unheated portions of the rod, which protrude from the heating coil on either side, experience convection with the ambient air at T∞ = 20 °C and h = 10 W/m2K. Assume that there is no convection...

  • 2. A brass rod 5 m long and 0.01 m in diameter increases in length by...

    2. A brass rod 5 m long and 0.01 m in diameter increases in length by 0.03 m whern its temperature is increased by 500° C. A similar brass rod of length 10 m has a diameter of 0.02 m. By how much will this rod's diameter increase if its temperature is increased by 1000o C? Brass rod

  • A cylindrical fuel rod 50mm in diameter has a uniform internal heat generation of ??1̇ =...

    A cylindrical fuel rod 50mm in diameter has a uniform internal heat generation of ??1̇ = 7*107 W/m3 . Under steady-state conditions, the temperature distribution is ??(??) = ?? + ????2, where T is in Celsius, ?? is in meters, ?? = 750°C, and ?? = -5.40*105 °C/m2 . The fuel rod properties are k=25 W/(m K), density= 1100 kg/m3 , and cp = 750 J/(kg K). (a) Determine the heat transferred (in Watts) at r=0 (centerline) and r=ro (outer...

  • One end of a long rod 3 cm in diameter is inserted into a furnace with the

    One end of a long rod 3 cm in diameter is inserted into a furnace with the (3 outer end projecting into the outside air. Once the steady state is reached the temperature of the rod is measured at two points, 15 cm apart and found to be 140°C and 100°C, when the atmospheric air is at 30°C with convection coefficient of 20 W/m2.K. Calculate the thermal conductivity of *.the rod material Consider a stainless steel spoon(k = 15.1 W/m.K), partially...

  • A 1.60 m cylindrical rod of diameter 0.550 cm is connected to a power supply that...

    A 1.60 m cylindrical rod of diameter 0.550 cm is connected to a power supply that maintains a constant potential difference of 14.0 V across its ends, while an ammeter measures the current through it. You observe that at room temperature (20.0 ∘C) the ammeter reads 18.3 A , while at 92.0 ∘C it reads 17.3 A . You can ignore any thermal expansion of the rod. 232 Electric Current Exercise 25.11 Constants PartA A 1.60 m cylindrical rod of...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT