ZuoTi.Pro
Question

A 3 volt DC power source required for a circuit is obtained by connecting together two...

A 3 volt DC power source required for a circuit is obtained by connecting together two 1.5V batteries in series. If the error in the voltage output of each battery is specified as ±1%, calculate and select the likely maximum possible error in the 3 volt power source that they make up ?

engineering   Electrical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

0 0
Add a comment
Know the answer?
Add Answer to:
A 3 volt DC power source required for a circuit is obtained by connecting together two...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • A 3 volt d.c. power source required for a circuit is obtained by connecting together two...

    A 3 volt d.c. power source required for a circuit is obtained by connecting together two 1.5V batteries in series. If the error in the voltage output of each battery is specified as ±1%, calculate the likely maximum possible error in the 3 volt power source that they make up.

  • It is required to use a FULL-wave rectifier to design a dc power supply that provides...

    It is required to use a FULL-wave rectifier to design a dc power supply that provides an average dc output voltage of 15 V. A maximum ripple voltage of ±1 V is allowed on the output voltage. The output voltage will feed a load resistance of 250 Ω. Assume a sinusoidal input voltage with the frequency of 60 Hz. Do not include a Zener diode in your design. (Assume V_D0)* = 0.7 V). a) Draw the circuit diagram. b) Calculate...

  • 1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliv...

    1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...

  • 3. A circuit has a 24VDC power source and a lamp with a resistance of 1202....

    3. A circuit has a 24VDC power source and a lamp with a resistance of 1202. What is the current in the circuit? 4. A circuit has ten (10) 12V batteries connected in series. What is the voltage available in the circuit? 5. A circuit has three loads connected in parallel, 13.5A, 12.75A and 10.25A. What is the total current needed for the circuit?

  • A small heater can be created by connecting a 10-ohm resistor across a 24-volt battery. Assume...

    A small heater can be created by connecting a 10-ohm resistor across a 24-volt battery. Assume the battery is an ideal 24-volt potential source, and that any wires used to connect the battery to the resistor are also ideal and have negligible resistance. Part A) Calculate the power dissipated as heat by this circuit. (Answer in Watts) Part B) 4.18 Joules of energy are required raise 1.0 mL of water by 1∘ C. We wish to modify our 24-volt heater...

  • A circuit consists of a 3-volt battery; connecting wires with very low resistivity; a light bulb...

    A circuit consists of a 3-volt battery; connecting wires with very low resistivity; a light bulb with resistance = 2Ω. a. How much current is flowing through the bulb? b. How much energy per second is converted from electrical potential energy to light and heat? c. If the bulb is replaced with one with higher resistance, in what way (increase, decrease, stay the same) would voltage and current change?

  • Prelab 3: The following circuit demonstrates the correct way to connect two car batteries together for...

    Prelab 3: The following circuit demonstrates the correct way to connect two car batteries together for the purposes of charging the bad battery. Good r1 Bad r2 Battery Battery Jumper Cables Figure 16: A single loop circuit illustrating the correct way to charge a car battery. Here we are modeling a real battery by having an ideal battery that supplies a voltage E in series with a resistance r. Real batteries have some internal resistance. In a real battery, the...

  • 4. A set of batteries are put into a circuit. a. Explain if how it is...

    4. A set of batteries are put into a circuit. a. Explain if how it is possible for the terminal voltage to be less than, equal to, and/or greater than the emf of the batteries. b. Discuss how the batteries can be arranged to reduce internal resistance, and the affect this would have on the terminal voltage. 7.2.24 4. Suppose the voltage output of a battery is 10.0V in a parallel circuit, and the resistances are Ri=4.0002, Rz=5.00., and R3=6.092....

  • (a) Two three-phase, 400kV (rms), 50Hz, AC networks are connected together via a current-source HVDC link...

    (a) Two three-phase, 400kV (rms), 50Hz, AC networks are connected together via a current-source HVDC link made up of a three-phase, 12-pulse full-wave thyristor rectifier and a three-phase, 12-pulse full-wave thyristor inverter. (i) Draw the circuit diagram for this system and explain, for the rectifier stage, how the firing delay angle may be used to control the average DC voltage. (ii) Explain the main advantages of HVDC transmission compared to AC transmission. (b) An H-Bridge converter is to be used...

  • We have a series RLC circuit with an AC voltage source: The resistance is 100Ohm, the inductance ...

    We have a series RLC circuit with an AC voltage source: The resistance is 100Ohm, the inductance is 10mH, the capacitance is 10mF. Select all the right answers. At 60Hz What is true? Question 10 options: The current through the inductor is larger than through the resistor The voltage across the inductor is larger than the voltage across the capacitor The voltage is lagging behind the current at the source The voltage and the current are in phase at the...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT