In a large battery-storage system, the rated output voltage of a battery string is 650V (dc)...
In a large battery-storage system, the rated output voltage of a battery string is 650V (dc) and the rated current is 1200A. The voltage can vary in a range from 500V to 800V. This output voltage is boosted to 900V (dc), as an input to an inverter that interfaces with the three-phase utility grid. A switching power-pole with a bi-directional power capability is used. The switching frequency is selected to be 50kHz, and the inductor value is selected such that the peak-to-peak ripple in the inductor current is less than 10% of the rated battery current, with the battery voltage at its rated value.
(a) Calculate the inductance value.
(b) Calculate the peak-to-peak ripple in the inductor current if operating at the rated current but the battery voltage is at its minimum.
(c) Repeat part (b) if the battery voltage is at its maximum.
Homework Answers
Add Answer to:
In a large battery-storage system, the rated output voltage of a
battery string is 650V (dc)...
1. (35 points) Switch mode DC DC Converters. a. (15 points) Design a flyback DC/DC power converter to the following specifications. Assume ideal components Input Voltage Output Voltage Output Powe...
1. (35 points) Switch mode DC DC Converters. a. (15 points) Design a flyback DC/DC power converter to the following specifications. Assume ideal components Input Voltage Output Voltage Output Power Switching frequency Maximum Current Ripple in the filter inductor Output ripple voltage: Continuous conduction 170 VDC 12 VDC 40 Watts 750 kHz 1.2 Amps Your answer should include a circuit diagram with each energy storage element labeled with its value. Label the transformer turns ratio.
1. (35 points) Switch mode...
power electronics and divices In one application, a 12V battery is to be used to power up six power LEDs connected a...
power electronics and divices
In one application, a 12V battery is to be used to power up six power LEDs connected as shown in Figure 3. The LED parameter is given Table 1. Using the rated parameters as the basis calculation, design a suitable DC-DC converter for this application whereby the inductor current variation must not exceed 50% of the output current whereas the output voltage ripple must be less than 5%. The system uses 200 kHz switching frequency Vo...
A PV array with terminal voltage around 48 V under standard conditions is connected to a step-up dc-dc converter to supply a load at 120 V, 5 A. The input inductance is 8 mH with an internal resistanc...
A PV array with terminal voltage around 48 V under standard conditions is connected to a step-up dc-dc converter to supply a load at 120 V, 5 A. The input inductance is 8 mH with an internal resistance of 0.2 ohms, and the switching frequency is 5 kHz. Assuming ideal circuit components, calculate the duty ratio (k) and average input current (I1). Evaluate the maximum peak-to-peak input current ripple for the converter. If this current is limited to 2% of...
A battery charger requires a DC-DC nuck converter to reduce the 380VDC voltage coming from the...
A battery charger requires a DC-DC nuck converter to reduce the 380VDC voltage coming from the rectification of the three phase mains voltage . Calculate the value of the duty cycle, inductance, and capacitance required to meet the following specifications: Vi(voltage input)=320V, Vo=100V,Fs(swith frecuency)=30kHz,Po(out put power)=20Kw, ΔiL(current ripple=10%IL, ΔvC(voltage ripple)=5%VC
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage ripple:max 20mV Load power: Switching frequency: 15kHz 110-125V 300V 1.5kW Calculate: (i) Maximum duty cycle (ii) Minimum duty cycle (iii) Average diode current (iv) Assuming the Rds(on) of the MOSFET is 0.01 Ω, and the diode forward voltage is 0.8V, calculate the approximate efficiency of the circuit. 2. A switching power supply shown in the circuit below has its switch driven by a signal...
1. Consider the single-phase VSI inverter shown below dc VR(t) iz(t) a) If your input voltage Vdc...
1. Consider the single-phase VSI inverter shown below dc VR(t) iz(t) a) If your input voltage Vdc - 100V2 V and switching frequency is 60 Hz with zero delay angle. Then, sketch the square wave output. Mark the peak values [10 marks] b) Sketch the fundamental output on the top of the above waveform. Mark the peak value По marksl c) The above A VSI is used to create a square wave output with 100v2 V at 60 Hz. This...
18 marks load with a power of 25.6 W.The cy f is 40kHz. sign a buck-boost converter to produce an output voltage of 16V a put voltage ripple must not exceed 1%. The dc input voltage is 24V. Th e swit...
18 marks load with a power of 25.6 W.The cy f is 40kHz. sign a buck-boost converter to produce an output voltage of 16V a put voltage ripple must not exceed 1%. The dc input voltage is 24V. Th e switching frequen 121 a) the duty ratio b) Find the size of the inductor so that the maximum inductor current c) the size of the capacitor d) Assume L=1 00μH and the switching frequency fis variable. 141 121 Lma 10A...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage 12 V. Switching frequency is 15 kHz. Calculate duty ratios for the switch and the diode. Find values for the inductor L and capacitor C, when the allowed output voltage ripple is ±0.15 % and the inductor current ripple is ±1 % (of the average value). If the on-time of the switch has an inaccuracy of ±50 ns, what is the new output voltage...
A buck converter is operating in the steady state with an input voltage of = 42 V dc, D = 0.3, ou...
A buck converter is operating in the steady state with an input voltage of = 42 V dc, D = 0.3, output power of 24 W, an inductance of 25 H and a switching frequency of 400 kHz. Draw the input current, inductor current, inductor voltage, and capacitor current waveforms. Assume the dc component of the inductor current flows through to the load and the ac component of the inductor current flows through the capacitor. Assume ideal circuit components.
Problem 1: (40 points) A boost converter based power factor correction circuit needs to operate with...
Problem 1: (40 points) A boost converter based power factor correction circuit needs to operate with universal input voltage, i.e the input voltage can be either 120V (RMS)+/- 10% at 60 Hz or 240 V(RMS) +/- 10% at 50 Hz. The output voltage is regulated at 400 V DC and the maximum (average) output power is 1kW. The switching frequency is 200 kHz. (a) Calculate the value of inductance needed to keep its peak peak ripple current to be less...
1. (35 points) Switch mode DC DC Converters. a. (15 points) Design a flyback DC/DC power converter to the following specifications. Assume ideal components Input Voltage Output Voltage Output Power Switching frequency Maximum Current Ripple in the filter inductor Output ripple voltage: Continuous conduction 170 VDC 12 VDC 40 Watts 750 kHz 1.2 Amps Your answer should include a circuit diagram with each energy storage element labeled with its value. Label the transformer turns ratio.
1. (35 points) Switch mode...
power electronics and divices
In one application, a 12V battery is to be used to power up six power LEDs connected as shown in Figure 3. The LED parameter is given Table 1. Using the rated parameters as the basis calculation, design a suitable DC-DC converter for this application whereby the inductor current variation must not exceed 50% of the output current whereas the output voltage ripple must be less than 5%. The system uses 200 kHz switching frequency Vo...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage ripple:max 20mV Load power: Switching frequency: 15kHz 110-125V 300V 1.5kW Calculate: (i) Maximum duty cycle (ii) Minimum duty cycle (iii) Average diode current (iv) Assuming the Rds(on) of the MOSFET is 0.01 Ω, and the diode forward voltage is 0.8V, calculate the approximate efficiency of the circuit. 2. A switching power supply shown in the circuit below has its switch driven by a signal...
1. Consider the single-phase VSI inverter shown below dc VR(t) iz(t) a) If your input voltage Vdc - 100V2 V and switching frequency is 60 Hz with zero delay angle. Then, sketch the square wave output. Mark the peak values [10 marks] b) Sketch the fundamental output on the top of the above waveform. Mark the peak value По marksl c) The above A VSI is used to create a square wave output with 100v2 V at 60 Hz. This...
18 marks load with a power of 25.6 W.The cy f is 40kHz. sign a buck-boost converter to produce an output voltage of 16V a put voltage ripple must not exceed 1%. The dc input voltage is 24V. Th e switching frequen 121 a) the duty ratio b) Find the size of the inductor so that the maximum inductor current c) the size of the capacitor d) Assume L=1 00μH and the switching frequency fis variable. 141 121 Lma 10A...
Problem 1: (40 points) A boost converter based power factor correction circuit needs to operate with universal input voltage, i.e the input voltage can be either 120V (RMS)+/- 10% at 60 Hz or 240 V(RMS) +/- 10% at 50 Hz. The output voltage is regulated at 400 V DC and the maximum (average) output power is 1kW. The switching frequency is 200 kHz. (a) Calculate the value of inductance needed to keep its peak peak ripple current to be less...
Most questions answered within 3 hours.
-
If the vapor pressure of carvone is approximately 9.4 torr at 99
°C, approximately how much...
asked 2 minutes ago -
A juice bottling company is carrying out a test at 10%
significance that the mean population...
asked 14 minutes ago -
What is the reflectivity (in percent) needed to keep water at a
temperature near its freezing...
asked 17 minutes ago -
Suppose that the average surface temperature of Earth is 300K.
Assume this is uniform over its...
asked 17 minutes ago -
Draw the condensed structural formula for alkenes and alkynes or
the line-angle structural formula for cycloalkenes...
asked 17 minutes ago -
M. Laing has suggested a new arrangement of the periodic table
(J.Chem.Ed.1989, 66,
746). Answer the following...
asked 38 minutes ago -
Café Michigan's manager, Gary Stark, suspects that demand for
mocha latte coffees depends on the price...
asked 38 minutes ago -
A US merchant purchases wine from a vineyard outside of Paris.
The wine is transported to...
asked 44 minutes ago -
we have (TTN)*
We have to use just one 2-bit counter with 1-bit global
history?
and...
asked 45 minutes ago -
Firms that fail to compete with lower prices and/or better
products will go bankrupt. Does this...
asked 45 minutes ago -
Question 1 Current and Resistance
Part A: A current of -14.5 nanoamperes is how many electrons...
asked 47 minutes ago -
The population standard deviation for the height of college
basketball players is 3.4 inches. If we...
asked 58 minutes ago