a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that...

Question

Question

a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that...

a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that is drawing 5 amp. what will the ammeter read as the total amperage?

engineering Electrical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

Current through clamp on ammeter is measured in a non contact way.

To measure the current through 120 V supply, first we need to connect the load so that a current should flow in the circuit. Adjust your meter knob to AC current and Clamp the meter on a wire coming from 120V supply, and it will show you the total current drawn from the supply.

The way mentioned in question is a way to measure voltage not current.

If you try to measure current by that way, it will damage your meter.

Please thumbs up

Add a comment

Answer 2

Similar Homework Help Questions

In the circuit shown in the diagram below, two thick wires connect a 1.4 volt battery...

In the circuit shown in the diagram below, two thick wires connect a 1.4 volt battery to a Nichrome (NIC) wire. Each thick connecting wire is 14 cm long, and has a radius of 9 mm. The thick wires are made of copper, which has 8.35+28 mobile electrons per cubic meter, and an electron mobility of 0.00434 (m (V/m). The Nichrome wire is 8 cm long, and has a radius of 4 mm. Nichrome has 9e+28 mobile electrons per cubic...
For the circuit shown in the figure, both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.45 A.

For the circuit shown in the figure, both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.45 A.a) What does the voltmeter read?b) What is the emf ε of the battery?
For the circuit shown in (Figure 1) both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.40 A.

For the circuit shown in (Figure 1) both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.40 A. Part A What does the voltmeter read?Part B What is the emf & of the battery?

The circuit below has the same reading on the ammeter when both switches are open and...

The circuit below has the same reading on the ammeter when both switches are open and when both switches are closed. What is the resistance R?
3. Explain the pros and cons of using aluminum wires instead of copper (4 points) 4....

3. Explain the pros and cons of using aluminum wires instead of copper (4 points) 4. Compare the EMT and RMC raceways. When is RMC required? (3 points) 5. Calculate the voltage drop between a distribution panel supplying 120 V to an electrical device that is 200 ft. away from the panel (one circuit - one phase) if the amperage is current = 15 A and copper wires of AWG 14 are used. What is the Voltage available at this...
dwelling un 4. Type NM-B Cable enters a metal device box and is secured by a cable clamp at the bottom of the box....

dwelling un 4. Type NM-B Cable enters a metal device box and is secured by a cable clamp at the bottom of the box. The cable is installed so the cable jacket extends "1/4 in. (6 mm beyond the cable clamp and free conductors begin at the end of the cable jacket a shown in Figure 1.39. If the device box has a depth of 3.5 in. (90 mm), the minimum permitted length of free conductor in this box is...

The circuit shown has three identical resistors in series with device for measuring current (an ammeter)....

The circuit shown has three identical resistors in series with device for measuring current (an ammeter). The value of the emf shown is 9.99 V,9.99 V, and each resistor has a value of 120 Ω.120 Ω. Part A: What is the total resistance of this circuit (?eq)?(Req)? ?eq=Req= ΩΩ Part B: What is the value of the current (?)(I) flowing out of the emf? ?=I= A Part C: What is the value of the voltage drop (Δ?)(ΔV) across the second...
Two wires are anchored at both ends. Wire 1 has a mass of 169 gm and...

Two wires are anchored at both ends. Wire 1 has a mass of 169 gm and a length of 4.10 m. Wire 2 has a mass of 50.0 grams, a length of 20.0 m, and a tension of 96.0 N. What must be the tension in Wire 1 if its third harmonic is to equal the first overtone of Wire 2? (Rounded to 3 significant figures)
P48 In the circuit shown in Figure 18.110, the two thick wires and the thin wire are made of Nich...

Please answer P48 P48 In the circuit shown in Figure 18.110, the two thick wires and the thin wire are made of Nichrome. Figure 18.110 (a) Show the steady-state electric field at the locations indicated, including in the thin wire. (b) Carefully draw pluses and minuses on your own diagram to show the approximate surface-charge distribution in the steady state. Make your drawing show clearly the differences between regions of high surface-charge density and regions of low surface-charge density. (c)...

For the circuit shown in the figure both meters are idealized, the battery has no appreciable...

For the circuit shown in the figure both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.55 A.1.What does the voltmeter read?2.What is the emf ε of the battery?

a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that...

Homework Answers

Add Answer to:
a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that...

Post as a guest

Earn Coins

In the circuit shown in the diagram below, two thick wires connect a 1.4 volt battery...

For the circuit shown in the figure, both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.45 A.

For the circuit shown in (Figure 1) both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.40 A.

The circuit below has the same reading on the ammeter when both switches are open and...

3. Explain the pros and cons of using aluminum wires instead of copper (4 points) 4....

dwelling un 4. Type NM-B Cable enters a metal device box and is secured by a cable clamp at the bottom of the box....

The circuit shown has three identical resistors in series with device for measuring current (an ammeter)....

Two wires are anchored at both ends. Wire 1 has a mass of 169 gm and...

P48 In the circuit shown in Figure 18.110, the two thick wires and the thin wire are made of Nich...

For the circuit shown in the figure both meters are idealized, the battery has no appreciable...

a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that...

Homework Answers

Add Answer to: a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that...

Post as a guest

Earn Coins

Add Answer to:
a clamp on ammeter has both wires clamped on a teo wire 120 volt circuit that...