Question

You have a thermistor (a varying resistor), a 10 kohm resistor, and an Arduino board. Draw...

You have a thermistor (a varying resistor), a 10 kohm resistor, and an Arduino board. Draw a circuit diagram to measure ambient temperature. You can draw a rectangle to represent the Arduino board, but you need to show which pins are used.

0 0
Add a comment Improve this question Transcribed image text
Answer #1

In the above circuit what is happening is,

The first pin of thermistor is given positiove 5 v supply from 5v pin of Arduino

The second pin of thermistor is connected to resistance in series and is connected to To A0 pin of the Arduino.

As thermistor changes the resistance within it, which in turn changes the voltage that is potential drop across the output pin of thermistor. So this variation in analog voltage is converted into the digital form by Anolg To Digital converted pin A0 of Arduino.

The resistance 10 k is further connected to ground to complete the circuit and protect the thermistor.

Add a comment
Know the answer?
Add Answer to:
You have a thermistor (a varying resistor), a 10 kohm resistor, and an Arduino board. Draw...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • op amp LM358N is used. This device is actually temperature measurement. Instead of resistor of 174Ohms, it should be a...

    op amp LM358N is used. This device is actually temperature measurement. Instead of resistor of 174Ohms, it should be a RTD or PT100, but I don't have in the lab right now, so this is simulation. With this resistance, temperature should be around 188-189 Celsius. I hope this part is clear. In the lab, for different temperatures I will put different resistor, 190 Ohms, 280 Ohms etc. Output of the amplifiers should be connected to pins A0 and A1 on...

  • Calibration and sensing Consider a thermistor temperature sensor (Fig. 1) with a pull-up resistor...

    using matlab to find steps 1-10 Calibration and sensing Consider a thermistor temperature sensor (Fig. 1) with a pull-up resistor R1 connected to a 10-bit analog-to-digital (ADC) converter (a full scale No-210-1=1023 counts corresponding to the reference voltage Vref). The thermistor is used to measure temperature in the total input span from -10°C to 110°C. knots n(t VO R1 A/D GND Temperature Fig. 1 The output count of the thermistor measurements circuit can be modeled by a nonlinear function of...

  • This is one original diagram for you to see what kind of circuit we have: Draw out the circuit d...

    This is one original diagram for you to see what kind of circuit we have: Draw out the circuit diagrams for these tasks. Each task is a separate task and you will need to construct a specific circuit for each task, as well as indicate where the measurement is taking place. 1. Specific Voltage From a 5V power supply, have a drop of 3.3V over a specific resistor accurate to the 0.1V mark. (Please point out which specific resistor if...

  • EXERCISE 2: USING PHASORS FOR A DRIVEN RC CIRCUIT 10. On the middle set of axes,...

    EXERCISE 2: USING PHASORS FOR A DRIVEN RC CIRCUIT 10. On the middle set of axes, draw phasors for k and ε using the provided ve phasor as a basis for a circuit in which R- 2Xc. Start by deciding what the peak voltage across the capacitor must be compared to the peak voltage across the resistor and then draw the appropriate Vc phasor We will consider a circuit consisting of a time varying emf in series with a capacitor...

  • You have a 10 ohm resistor connected in series with an ammeter. The voltage applied to...

    You have a 10 ohm resistor connected in series with an ammeter. The voltage applied to the whole circuit is 1.2 volts. At the same time you have a voltmeter connected across the 10 ohm resistor and voltmeter reads 0.9 volts. The circuit draws a total of 0.5 amps. Can you determine resistance of the ammeter?

  • You have a 250-Ω resistor and a 0.360-H inductor. Suppose you take the resistor and inductor...

    You have a 250-Ω resistor and a 0.360-H inductor. Suppose you take the resistor and inductor and make a series circuit with a voltage source that has a voltage amplitude of 31.0 V and an angular frequency of 200 rad/s. Q]Construct the phasor diagram. Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded. Include: 1) Vr (Resistor Voltage Phasor), 2) Vl (Inductor Voltage Phasor) and 3) I (Current Phasor)

  • Answer the following question. You must draw a schematic of the problem, clearly indicate the governing...

    Answer the following question. You must draw a schematic of the problem, clearly indicate the governing equation, list all units with all numbers/calculations, show all work in an orderly manner, and give your final answer in a complete sentence. 13. A very thin IC Chip, embedded on top of a Printed Circuit board is intended to dissipate 2.8W of heat. The 1.5cm by 1.5cm chip is cooled convectively on the top with air at 20C and a convective coefficient of...

  • Assume that you have a circuit containing a capacitor (15 mu F) and a resistor (200...

    Assume that you have a circuit containing a capacitor (15 mu F) and a resistor (200 ohm) in series with an AC power generator with f = 60Hz and element_m = 36.0V. What are (a) Z, (b) psi and (c) I? (d) Draw a phasor diagram.

  • 4) Given the circuit below. The voltage is 5 volts and each resistor is 10 ohms....

    4) Given the circuit below. The voltage is 5 volts and each resistor is 10 ohms. The current flowing through the circuit (when measured by an ideal ammeter) is 1 amp. a) Show current through the circuit is 1 A. Next, assume you put a DMM (in ammeter mode) which has a resistance of one ohm at point A. Recalculate the equivalent resistance of the circuit. b) What is the current flowing through the circuit now. This is the current...

  • This question is about the Arduino code. Please complete a 4-input circuit on your Arduino. Your...

    This question is about the Arduino code. Please complete a 4-input circuit on your Arduino. Your circuit, in addition to cycling through a binary representation of the numbers 0-15 using LEDs, should use the Serial port to output the decimal equivalent of each of the numbers in the format: Output: 15 ... if the value was 1111, and so forth. You will be asked to upload your code as well as a photo of your working breadboard circuit. Add comments...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT