An amplifier has an open-circuit voltage gain of 160. With a 10 kΩ load connected, the...
An amplifier has an open-circuit voltage gain of 160. With a 10 kΩ load connected, the voltage gain is found to be only 80.
Find the output resistance of the amplifier.
Ro=
Homework Answers
Add Answer to:
An amplifier has an open-circuit voltage gain of 160. With a 10
kΩ load connected, the...
A signal source with an open-circuit voltage of Vs = 2 mV rms and an internal...
A signal source with an open-circuit voltage of Vs = 2 mV rms and an internal resistance of 50 kΩ is connected to the input terminals of an amplifier having an open-circuit voltage gain of 100, an input resistance of 135 kΩ , and an output resistance of 4 Ω. A 4 Ω load is connected to the output terminals. Find Voltage gain Avs = V0/Vs Find voltage gain Av = V0/Vi Find current gain Ai Find power gain G...
1.14 An amplifier with a voltage gain of +40 dB, an input resistance of 10 kS2, and an output resistance of i kn is used to drive a l-kΩ load. What is the value of Apo? Find the value of the po...
1.14 An amplifier with a voltage gain of +40 dB, an input resistance of 10 kS2, and an output resistance of i kn is used to drive a l-kΩ load. What is the value of Apo? Find the value of the power gain in decibels.
1.14 An amplifier with a voltage gain of +40 dB, an input resistance of 10 kS2, and an output resistance of i kn is used to drive a l-kΩ load. What is the value of...
electronics question #3 (5 pts.) A BJT amplifier has the voltage gain of 80, absolute voltage gain of 60, current gain of 40, and source resistance of 1 k2. Find the load resistance (no need to kn...
electronics question
#3 (5 pts.) A BJT amplifier has the voltage gain of 80, absolute voltage gain of 60, current gain of 40, and source resistance of 1 k2. Find the load resistance (no need to know the circuit or amplifier type).
#3 (5 pts.) A BJT amplifier has the voltage gain of 80, absolute voltage gain of 60, current gain of 40, and source resistance of 1 k2. Find the load resistance (no need to know the circuit or...
The output voltage of a voltage amplifier has been found to decrease by 40 % when...
The output voltage of a voltage amplifier has been found to decrease by 40 % when a load resistance of 4 kΩ is connected. What is the value of the amplifier output resistance?
A voltage amplifier (not necessarily an op amp) has a gain of 100 V/V when its...
A voltage amplifier (not necessarily an op amp) has a gain of 100 V/V when its output is left open-circuited. However, when the amplifier’s output is loaded with 1.0 kΩ, the gain is only 85 V/V. The same voltage amplifier has an input impedance of 10 kΩ. If the amplifier’s output is left open-circuited but the source driving the amplifier has a Th´evenin resistance (that is, a source impedance) of 150 Ω, then the gain will be less than 100...
Draw and explain the gain frequency characteristic of a resistance–capacitance-coupled amplifier. Reference should be made to...
Draw and explain the gain frequency characteristic of a resistance–capacitance-coupled amplifier. Reference should be made to mid-band frequencies and to cutoff points. An amplifier has an open-circuit voltage gain of 800, an output resistance of 20 Ω and an input resistance of 5 kΩ. It is supplied from a signal source of e.m.f. 10 mV and internal resistance 5 kΩ. If the amplifier supplies a load of 30 Ω, .
&nb
Please solve all for me Q1. An inverting amplifier circuit design has an input resistance R1 = 10 kΩ, and feedback resistance R2 = 25 kΩ and an input voltage source VS = 0.5V. Sketch the circuit diagram and find the voltage gain Av in dB, output voltage vo, input source current is, feedback current i2, and output current io of the amplifier circuit. What is the operating bandwidth of this amplifier circuit? Q2. Design an inverting amplifier circuit...
SCSC Integrated Circuit Manufacturing LLC will market an amplifier circuit with a voltage gain of +40dB,...
SCSC Integrated Circuit Manufacturing LLC will market an amplifier circuit with a voltage gain of +40dB, input resistance Rin=10k Ohm and output resistance 1k Ohm. This amplifier is designed to drive a 1k Ohm purely resistive load. Based on design calculations the input power to the load in terms of the input voltage is determined to be 3.52i. Find the power gain in dB
Example 6-5 & 6-6 page 284 Calculate the base-to-collector voltage gain of the amplifier in the f...
Example 6-5 & 6-6 page 284 Calculate the base-to-collector voltage gain of the amplifier in the figure below both without and with an emitter bypass capacitor if there is no load resistor +12V Rc C3 22 ㏀ 2N3904 v- Calculate the base-to-collector voltage gain of the amplifier when a load resistance of 5K2 is connected to the output .The emitter is effectively bypassed and r 6.582 R2 6.8 kΩ 560 Ω
Example 6-5 & 6-6 page 284 Calculate the base-to-collector...
A CE amplifier utilizes a BJT with β = 100 biased at IC = 0.5 mA;...
A CE amplifier utilizes a BJT with β = 100 biased at IC = 0.5 mA; it has a collector resistance RC = 10 kΩ. Find Rin, Ro, and Avo. If the amplifier is fed with a signal source having a resistance of 10 kΩ, and a load resistance RL =10 kΩ is connected to the output terminal, find the resulting Av and Gv. If the peak voltage of the sine wave appearing between base and emitter is to be...
1.14 An amplifier with a voltage gain of +40 dB, an input resistance of 10 kS2, and an output resistance of i kn is used to drive a l-kΩ load. What is the value of Apo? Find the value of the power gain in decibels.
1.14 An amplifier with a voltage gain of +40 dB, an input resistance of 10 kS2, and an output resistance of i kn is used to drive a l-kΩ load. What is the value of...
electronics question
#3 (5 pts.) A BJT amplifier has the voltage gain of 80, absolute voltage gain of 60, current gain of 40, and source resistance of 1 k2. Find the load resistance (no need to know the circuit or amplifier type).
#3 (5 pts.) A BJT amplifier has the voltage gain of 80, absolute voltage gain of 60, current gain of 40, and source resistance of 1 k2. Find the load resistance (no need to know the circuit or...
Example 6-5 & 6-6 page 284 Calculate the base-to-collector voltage gain of the amplifier in the figure below both without and with an emitter bypass capacitor if there is no load resistor +12V Rc C3 22 ㏀ 2N3904 v- Calculate the base-to-collector voltage gain of the amplifier when a load resistance of 5K2 is connected to the output .The emitter is effectively bypassed and r 6.582 R2 6.8 kΩ 560 Ω
Example 6-5 & 6-6 page 284 Calculate the base-to-collector...
Most questions answered within 3 hours.
-
Why [M(CN)6] is not organometallic even it has metal
to carbon bond too
asked 2 minutes from now -
mstar electric has a bond issue outstanding that has a 20 year
life, a $1,000 par...
asked 5 minutes ago -
This is a Business Writing Question:
Common Types of Faulty Sentence Logic:
A. Mixed constructions
B....
asked 6 minutes ago -
Skinner asserts that science, and the common view of science, has
been tarnished. Explain his evidence...
asked 8 minutes ago -
Question 3 (1 point)
Fill in the blank. Speed Car Rental company found that the tire...
asked 9 minutes ago -
An short-seller in Tesla is worried the latest management
earnings forecast is too aggressive and the...
asked 9 minutes ago -
A grocery store's receipts show that Sunday customer purchases
have a skewed distribution with a mean...
asked 15 minutes ago -
A 0.035 mol sample of a weak acid, HA, is dissolved in 437 mL of
water...
asked 26 minutes ago -
a sample of Ar gas has a volume of 6.30 L with an unknown
pressure. the...
asked 27 minutes ago -
The
serum cholesterol levels of a population of kids follow a normal
distribution with mean 155...
asked 47 minutes ago -
han discusses the racist practice of badlands, a bar
in the Castro
district of San Francisco,...
asked 59 minutes ago -
A sample of final exam scores is normally distributed with a
mean equal to 25 and...
asked 1 hour ago