Design a relay-schematic ladder diagram to perform the following steps: Using FLUIDSIM A double-acting cylinder is...
Design a relay-schematic ladder diagram to perform the following steps: Using FLUIDSIM
- A double-acting cylinder is initially at fully-retract position. An electrical limit switch placed at the fully-retracted position will send a signal to the device described in Step 2.
- A double-solenoid 5/2 valve is placed right under the cylinder to control its motions.
- If an NO push button is pressed and released immediately, the double-acting cylinder will be moving forward with an adjustable speed
- When the cylinder is at its fully-extended position, it will be sensed by an electrical limit switch which will send a signal to the device stated in Step 2. The cylinder will be moving backward with a regular speed.
- The motion will be repeated until a reset button is pressed.
Homework Answers
Request Answer!
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Add Answer to:
Design a relay-schematic
ladder diagram to perform the following steps: Using
FLUIDSIM
A double-acting cylinder is...
Objectivel Design a simple pneumatic circuit design to activate a double-acting cylinder. Problems A roller track...
Objectivel Design a simple pneumatic circuit design to activate a double-acting cylinder. Problems A roller track is to be swiveled by means of a double acting cylinder. The signals to extend and to retract are given from separate push buttons. The cylinder is to remain in position indicated by the last signal until an opposing signal is given. The retracting speed must be adjustable. [Main components 1. 2. 3. Double-acting cylinder 5/2 directional control valve with pneumatic actuated on both...
A large double-acting cylinder will perform following motions: The forward and backward motion is controlled by...
A large double-acting cylinder will perform following motions: The forward and backward motion is controlled by a 5/2 flow control valve. When a normally-closed (N. C.) 3/2 valves is pressed and then released immediately, a piston will keep moving forward with maximum speed. When another NC 3/2 valves is pressed and released, the piston will move back with an adjustable speed.You need to submit the screenshots of the Fluidsim drawing and Assembly Platform circuit for this test.
Using Fluidsim, please design a pneumatic circuit so that a large double-acting piston is used to...
Using Fluidsim, please design a pneumatic circuit so that a large double-acting piston is used to punch a hole on a part. The piston won't be activated until the following conditions are met a. Two hands are pushed together on two separate push buttons (using two manual 3/2 valves anda two-pressure valve). roller-activated 3/2 valve). the piston retracts. b. A part is sensed by a roller-activated switch (a c. When either hand does not touch the push button, The forward...
design using FLUIDSIM Please solve as soon as possible ***The solution for PNEUMATICS 2. A double...
design using FLUIDSIM
Please solve as soon as possible
***The solution for
PNEUMATICS
2. A double acting cylinder is continuously punching a hole into a donut by pressing a START pushbutton. The workpiece is detected by a capacitive sensor and cylinder positions are sensed by magnetic reed sensors. The cylinder will extend very fast once a 6bar pressure is detected. The cylinder will go back to its initial position after reaching a fully extended position. Retraction speed is adjustable. Another...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Objectivel Design a simple pneumatic circuit design to activate a double-acting cylinder. Problems A roller track is to be swiveled by means of a double acting cylinder. The signals to extend and to retract are given from separate push buttons. The cylinder is to remain in position indicated by the last signal until an opposing signal is given. The retracting speed must be adjustable. [Main components 1. 2. 3. Double-acting cylinder 5/2 directional control valve with pneumatic actuated on both...
Using Fluidsim, please design a pneumatic circuit so that a large double-acting piston is used to punch a hole on a part. The piston won't be activated until the following conditions are met a. Two hands are pushed together on two separate push buttons (using two manual 3/2 valves anda two-pressure valve). roller-activated 3/2 valve). the piston retracts. b. A part is sensed by a roller-activated switch (a c. When either hand does not touch the push button, The forward...
design using FLUIDSIM
Please solve as soon as possible
***The solution for
PNEUMATICS
2. A double acting cylinder is continuously punching a hole into a donut by pressing a START pushbutton. The workpiece is detected by a capacitive sensor and cylinder positions are sensed by magnetic reed sensors. The cylinder will extend very fast once a 6bar pressure is detected. The cylinder will go back to its initial position after reaching a fully extended position. Retraction speed is adjustable. Another...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Most questions answered within 3 hours.
-
The labor force minus the number of employed equals the number
of unemployed.
a. True
b....
asked 18 minutes ago -
Determine the mass in units of grams [g] of 0.49 moles [mol]
of a new fictitious...
asked 40 minutes ago -
A horizontal mass of M=5kg is on a spring and stretched to
x=0.5m when released from...
asked 1 hour ago -
26 of 50
"I have worked at the Arizona Humane Society for ten years, and
have...
asked 2 hours ago -
Compare and contrast zero based budgeting and incremental (or
base year) budgeting.
asked 2 hours ago -
4 pts 10. Which of the following hypothesis would be MOST
difficult to test experimentally? Group...
asked 2 hours ago -
A business owner makes 1,000 items a day. Each day he or she
contributes eight hours...
asked 2 hours ago -
A
circular loop in the plane of a paper lies inca0.65 T magnetic
field pointing into...
asked 2 hours ago -
A business owner is trying to decide whether to buy, rent, or
lease office space and...
asked 2 hours ago -
Thermal Storage Solar heating of a house is much more efficient
if there is a way...
asked 2 hours ago -
Considering the “fits” for group and job design dimensions,
suppose you had 12 employees with different...
asked 3 hours ago -
Consider TCP connection management.
How many segments are typically involved in the TCP connection
establishment? What...
asked 3 hours ago