According to Chegg's policy experts are required to solve one question at a time or it's four subparts if any. Please upload the remaining questions separately.
A) A hole is poked through the metal side of a drum holding water. The hole...
The flow rate of a liquid through a 2.0 cm radius pipe is 0.008 m3/s. The average fluid velocity in the pipe is: 6.37 m/s 0.04 m/s 2.00 m/s 4.64 m/s 0.64 m/s How large a force is necessary to stretch a 2 mm ‑diameter steel wire by 1%? 6,280 N 3,140 N 12,560 N 9,420 N 7,650 N
A 2L bottle is filled with water and has a 2mm diameter hole in the side 2cm from the bottom and the top is open to the atmosphere. a) What is the velocity of the water stream coming out of the hole when the water is 10cm above the hole? Treat the water as an ideal fluid obeying Bernoulli's equation. Additionally, you may assume that the flow is slow enough that the velocity of the water at the top surface...
7. Water flows through a pipe of diameter 1.08m at a velocity of 2m/s. If someone puts a nozzle on the end of the pipe, reducing the diameter to 0.35m, at what speed will the water exit the pipe?. 10. A pipe with a radius of 50 cm has water flowing at 5 m/s. If water goes into a new pipe with radius 33 cm, how much will the pressure decrease? 11. A large dam has a hole that is...
5.6 A 7.5 cm diameter jet of water is directed at a hole in a vertically supported plate Some of the water spreads as a film over the surface of the plate and the remainder leaves horizontally through the hole. The angle between the jet and the plate is 65° and the velocity within the jet is uniform and 10 m/s. Assume inviscid flow and neglect gravity forces. The density of water is 1000 kg/m a) What is the velocity...
6. (25 points) Water at standard atmospheric conditions flows through a 100 m long plastic pipe with a circular cross section of diameter D = 0.2 m at an average velocity of 10 cm/s. The flow exits into the atmosphere. The pipe material is smooth and has essentially no roughness. What is the pressure at the pipe entrance if it is horizontal? What is the pressure at the pipe entrance if the elevation increases by 50 cm? A Moody diagram...
diameter the hole. of how 42. Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in Figure P14.42, the pressure is P1.75 X 101 Pa and the pipe diameter is 6.00 cm. At another point y0.250 m higher, the pressure is P2 1.20 X 104 Pa and the pipe diameter is 3.00 cm. Find the speed of flow (a) in the lower section and (b) in the upper section. (c) Find the volume flow...
1. Atall cylindrical tank, held above ground on stilts, is partially filled with water. (See top figure). The tank has a diameter, D. At time equal to zero, a hole of diameter d is poked in the bottom of the tank, where d<< D. Let z-0 correspond to the bottom of the tank. The initial fluid height is za. Had Use Bernoulli equation to assess the velocity of the fluid as it leaves the bottom of the tank as a...
In-class problem (submit by 5 pm) Water at a gauge pressure of 3.8 atm at street level flows into an office building at a speed of 0.06 m/s through a pipe 5.0 cm in diameter. The pipes taper down to 2.6 cm in diameter by the top floor, 20 m above. Calculate the flow velocity and the gauge pressure in such a pipe on the top floor. Assume no branch pipe an ignore viscosity.
a cylindrical water storage 12. in diameter and 8m high, is filled through a 100 mm pipe carrying a velocity of 40 m/s. (a) how long it will take to fill the tank? (b) if the tank has an out flow pipe at the bottom with a capacity of 0.12 m^3/s discharge rate and both inflow and outflow pipes are opened at the same time, compute the time rate of the rise of the water level. (c) compute the time...
7. Two round pipes have water flowing through them. Pipe B is half of the diameter of pipe A. If the average velocity of the flow through both pipes is the same, what is Q./Q.? B 8. A lubricating oil with a viscosity of 0.1 (N s/m' is between two plates, one stationary and one moving If the moving plate is moving with a velocity of 1.3 m/s and the distance between the plates is 0.4 cm what is the...