Will Rate! For design of a 10 Gigabits per second fiber optical communications system using a single mode semiconductor laser at 1550nm wavelength, a photodetector, and a single mode optical communication fiber. The spectral line-width of the semiconductor laser is 10 pm. The Fiber length is 150km.
a. What is the dispersion requirement for the optical fiber? [Hint: find out the requirement for dispersion coefficient at 1550nm]
b. What is the requirement for the response time of the photoconductor?
Will Rate! For design of a 10 Gigabits per second fiber optical communications system using a...
Problem 3 (25 points) A silicon photodetector has an internal photo responsivity of 0.5 A/Wt wavelength of 850 nm. When photons of wavelength 850 nm are incident normally on this photodetector, some photons are reflected back and some photons penetrate to the detection region and are absorbed by the photodetector. (a) The index of refraction of silicon is 3.45. If the electric current measured by this photodetector is 20 mA, what is the incident optical power? (b) Silicon has a...
(a) The optical gain coefficient of a semiconductor laser with 150 μm cavity length is shown in Fig 1. The loss coefficient and the refractive index of the semiconductor laser are 21.6 cm" and 3.5 respectively. Find (i)The minimum gain coefficient required for lasing (ii) The frequency separation between the longitudinal modes of the laser (iii) The number of longitudinal modes emitted (b) This laser is required to produce a single mode output at a wavelength of 1.32 unm If...
Photonics and Optical Revision Sheet 1 1. Caculate the photon energy in eV for a wavelength of 1.55 um 2, A 1.55 μm digital communications system operating at 4 GBits/s receives an average power of -24 dBm at the detector. On the assumption that 1 and 0 bits are equally likely to occur how many photons are received within each 1 bit? 3. A1.3 um digital communications system operating at 3 GBits/s receives an average power of -29 dBm at...
8. A 1550 nm optical link uses a standard single-mode fiber with dispersion parameter of 4 ps/nm/km (Chromatic Dispersion), and a laser source with a linewidth of 0.5 nm. Assuming the link carrier is a 10 Gbits/s binary signal, estimate the maximum length of optical fiber required before dispersion compensation is required. (Assume the maximum spread is half the time interval between each bit).
PLZ answer Both question with working Cheers Question 3 10 pts An optical fibre has a core diameter of 11 um, and an acceptance angle in air of 0.037 radians. Above what operating wavelength is the fibre single mode? 1.55 pm 1.36 um 0.09 um 1.31 pm O 0.43 um 2.71 um Question 4 10 pts An optical source has a spectral width of 4 nm. What type of optical source is it likely to be? OLED O Laser Diode...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
summatize the following info and break them into differeng key points. write them in yojr own words apartus 6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...