A) Draw the circuit diagram and design a half wave rectifier AC-DC converter to deliver 12V-DC...
A) Draw the circuit diagram and design a half wave rectifier AC-DC converter to deliver 12V-DC with a ripple of 10 mV for a load current of 0.5 A
- Design means to find the capacitor value and the ratio of the turns in the transformer
assuume the supply voltage is 120v and 60Hz
B) Calculate the Peak Inverse Voltage, average and max current through the diode.
Homework Answers
Add Answer to:
A) Draw the circuit diagram and design a half wave rectifier
AC-DC converter to deliver 12V-DC...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliv...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
A half-wave diode rectifier circuit is driven by a 60Hz sine wave with a peak value...
A half-wave diode rectifier circuit is driven by a 60Hz sine wave with a peak value of 19V. If the load resistance this circuit drives is 4.3kΩ and the ripple voltage at the output is 0.43 Vpeak-to-peak, then what is the peak current in the diode in milliamps? Answer: Check The diode circuit shown is a Select one: O a. Voltage doubler circuit O b. DC restorer circuit c. Limiter circuit O d. Peak detector circuit O e. None of...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
Use a transformer, a bridge rectifier IC, and a capacitor to design a battery charger. If...
Use a transformer, a bridge rectifier IC, and a capacitor to design a battery charger. If the input power is from the regular power line (120rms, 60Hz) and the battery is 12-V battery. The peak-to-peak ripple voltage across the battery should be no more than 2V. Assume the battery internal resistance is 100. 1) Draw the circuit diagram; 2) Explain how it works; 3) Specify the value of the turns ratio of the transformer and peak inverse voltage of diode....
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal wavef...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform from the wall power and convert it to a “regulated” dc value giving 15 volts +, - 1.0 volts across a 1200-ohm output load resistor with no more than 2% ripple voltage, all at a total component parts cost of less than $175.00 (US$). Your design process/ analysis is to be conducted by hand. Consider for this design task: Assume an ideal transformer and...
Exercise#2 • An AC supply of 230V rms is applied to a half wave rectifier circuit...
Exercise#2 • An AC supply of 230V rms is applied to a half wave rectifier circuit through a transformer of turn ratio 5:1. Assume the diode is an ideal one. The load resistance is 30092. * Find (a) peak load current (b) the dc load current (c) the rms load current (d) TUF (e) PIV (f) FF (g) RF (h) power delivered to load
In an AC to DC rectifier circuit, the output DC signal of the rectified wave was...
In an AC to DC rectifier circuit, the output DC signal of the rectified wave was measured to be VDC= (9.1±0.6)V and its ripple voltage was measured to be Vripple=(0.14±0.03) mV. What is the uncertainty on the quality factor of the rectifier? (Report your final value to 2 sig figs)
You need to design a DC power supply that provides an average DC output voltage of...
You need to design a DC power supply that provides an average DC output voltage of 5V to charge your cellphone. The maximum allowed ripple at the output is ±200 mV. Your cellphone can be modeled as a 1 50Ω load. You have to use a bridge rectifier with four diodes. Note: For calculations, consider constant voltage drop model of the diode with V0 = 0.7V. (a) The charger is designed to use in the US, i.e. transformer primary is...
D *4.80 It is required to use a peak rectifier to design a de power supply...
D *4.80 It is required to use a peak rectifier to design a de power supply that provides an average de output voltage of 12 V on which a maximum of ±1-V ripple is allowed. The rectifier feeds a load of 200 2. The rectifier is fed from the line voltage (120 V rms, 60 Hz) through a transformer. The diodes available have 0.7-V drop when conducting. If the designer opts for the half-wave circuit: (a) Specify the rms voltage...
It is required to use a FULL-wave rectifier to design a dc power supply that provides...
It is required to use a FULL-wave rectifier to design a dc power supply that provides an average dc output voltage of 15 V. A maximum ripple voltage of ±1 V is allowed on the output voltage. The output voltage will feed a load resistance of 250 Ω. Assume a sinusoidal input voltage with the frequency of 60 Hz. Do not include a Zener diode in your design. (Assume V_D0)* = 0.7 V). a) Draw the circuit diagram. b) Calculate...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
A half-wave diode rectifier circuit is driven by a 60Hz sine wave with a peak value of 19V. If the load resistance this circuit drives is 4.3kΩ and the ripple voltage at the output is 0.43 Vpeak-to-peak, then what is the peak current in the diode in milliamps? Answer: Check The diode circuit shown is a Select one: O a. Voltage doubler circuit O b. DC restorer circuit c. Limiter circuit O d. Peak detector circuit O e. None of...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
Exercise#2 • An AC supply of 230V rms is applied to a half wave rectifier circuit through a transformer of turn ratio 5:1. Assume the diode is an ideal one. The load resistance is 30092. * Find (a) peak load current (b) the dc load current (c) the rms load current (d) TUF (e) PIV (f) FF (g) RF (h) power delivered to load
You need to design a DC power supply that provides an average DC output voltage of 5V to charge your cellphone. The maximum allowed ripple at the output is ±200 mV. Your cellphone can be modeled as a 1 50Ω load. You have to use a bridge rectifier with four diodes. Note: For calculations, consider constant voltage drop model of the diode with V0 = 0.7V. (a) The charger is designed to use in the US, i.e. transformer primary is...
D *4.80 It is required to use a peak rectifier to design a de power supply that provides an average de output voltage of 12 V on which a maximum of ±1-V ripple is allowed. The rectifier feeds a load of 200 2. The rectifier is fed from the line voltage (120 V rms, 60 Hz) through a transformer. The diodes available have 0.7-V drop when conducting. If the designer opts for the half-wave circuit: (a) Specify the rms voltage...
Most questions answered within 3 hours.
-
A 8.15- g bullet from a 9-mm pistol has a velocity of 366.0 m/s.
It strikes...
asked 1 hour ago -
The outstanding bonds of Alpha Extracts have a yield to maturity
of 7.4 percent and a...
asked 1 hour ago -
The Problem: The Case of the Harmonizing Vacations
Your CEO is exploring partnering with a European...
asked 2 hours ago -
A chemical equation is balanced by adding coefficients in front
of some formulas so that the...
asked 2 hours ago -
From the literature (reference your sources): What are the
lattice parameters of calcite and aragonite? Why...
asked 3 hours ago -
Your system is rejecting the question am asking which is
preceded by a case study. It...
asked 3 hours ago -
3. On January 2, 2000, Larry creates a trust with himself as
trustee. Larry as trustee...
asked 3 hours ago -
A member of the volleyball team spikes the ball. During this
process, she changes the velocity...
asked 3 hours ago -
Are adult gamers less likely to use a gaming console (Xbox,
PlayStation, Wii, etc...) than teen...
asked 4 hours ago -
The University of
Texas recently reported that 43% of college students aged 18-24
would spend their...
asked 4 hours ago -
The length of stay at a specific emergency department in
Phoenix, Arizona, in 2009 had a...
asked 3 hours ago -
. Please give the mechanism for this type of problem. Step by
Step
The toxin that...
asked 3 hours ago