Assign each of the following discrete input and output addresses based on the ControlLogix format. a....
Assign each of the following discrete input and output addresses based on the ControlLogix format.
a. Limit switch connected to terminal screw 4 of the module in slot 1 of the chassis.
b. Pressure switch connected to terminal screw 2 of the module in slot 3 of the chassis.
c. Pushbutton connected to terminal screw 0 of the module in slot 6 of the chassis.
d. Pilot light connected to terminal screw 13 of the module in slot 2 of the chassis.
e. Motor starter coil connected to terminal screw 6 of the module in slot 4 of the chassis.
f. Solenoid connected to terminal screw 8 of the module in slot
5 of the chassis.
Homework Answers
-----------------------------------------------------------Answer-------------------------------------------------
The following discrete input and output addresses based on the ControlLogix format-
ANSWER A
Limit switch connected to terminal screw 4 of the module in slot 1 of the chassis
The addressing format is I:1/4
ANSWER B
Pressure switch connected to terminal screw 2 of the module in slot 3 of the chassis
The addressing format is I:3/2
ANSWER C
Pushbutton connected to terminal screw 0 of the module in slot 6 of the chassis.T
The addressing format is I:6/0
ANSWER D
Pilot light connected to terminal screw 13 of the module in slot 2 of the chassis.
O:2/13
ANSWER E
Motor starter coil connected to terminal screw 6 of the module in slot 4 of the chassis
O:4/6
ANSWER F
Solenoid connected to terminal screw 8 of the module in slot 5 of the chassis.
O:5/8
----------------------------------------THANK@YOU----------------------------------------------------------------
Add Answer to:
Assign each of the following discrete input and output addresses
based on the ControlLogix format.
a....
Note: The conveyor will be operated and programmed in Safety Mode (switch the conveyor output to...
Note: The conveyor will be operated and programmed in Safety Mode (switch the conveyor output to the NC position) so that the Motor will stop when it receives a signal. When the switch S_3 is activated, the conveyer is required to run (M_R OFF). When the conveyor is running the green light L_2 is to be energized The fiber optic sensor FP_S must count the TOTAL parts that go through the conveyor. The inductive sensor IP S must count the...
. What is a programmable logic controller (PLC)?12. The , Identify four tasks in addition to...
. What is a programmable logic controller (PLC)?12. The , Identify four tasks in addition to relay switching operations that PLCs are capable performing. 3. List six distinct advantages that PLCs offer over controller operates in real time. What does this mean? of performing 13. Answer the following with reference to the f conventional relay-based control systems. control PLC ladder logic diagram of Figure 1-21 this etary PLC architecture. 5. State two ways in which LVO is incorporated into 4,...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Note: The conveyor will be operated and programmed in Safety Mode (switch the conveyor output to the NC position) so that the Motor will stop when it receives a signal. When the switch S_3 is activated, the conveyer is required to run (M_R OFF). When the conveyor is running the green light L_2 is to be energized The fiber optic sensor FP_S must count the TOTAL parts that go through the conveyor. The inductive sensor IP S must count the...
. What is a programmable logic controller (PLC)?12. The , Identify four tasks in addition to relay switching operations that PLCs are capable performing. 3. List six distinct advantages that PLCs offer over controller operates in real time. What does this mean? of performing 13. Answer the following with reference to the f conventional relay-based control systems. control PLC ladder logic diagram of Figure 1-21 this etary PLC architecture. 5. State two ways in which LVO is incorporated into 4,...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Most questions answered within 3 hours.
-
Identify and describe in detail the four categories of
institutions that could be included in a...
asked 1 minute ago -
In python
class Customer:
def __init__(self, customer_id, last_name, first_name, phone_number, address):
self._customer_id = int(customer_id)
self._last_name =...
asked 8 minutes ago -
What is an example of a limitation in implementing a new
ERP system and how it...
asked 3 minutes ago -
In a section of 9.7cm of an artery with a radius of 2.6mm there
is a...
asked 4 minutes ago -
the two carboxylic acid groups of aspartic acid have different
acidities with pKa values of 2.1...
asked 8 minutes ago -
Would CuCO3 aqueous salt combined with calcium chloride
form a solid precipitate? If so, what would...
asked 7 minutes ago -
How do ECM Solutions assist in embedding a culture of continuous
improvement in an organization? (Project...
asked 28 minutes ago -
Directions
These directions introduce the idea of Essential Questions.
Since this may be a new concept...
asked 30 minutes ago -
1.b. Fiscal policy is said to suffer from ‘crowding out’.
Explain what this means and why...
asked 47 minutes ago -
The equation for the reaction of nitrogen and oxygen to form
nitrogen oxide is written as...
asked 52 minutes ago -
A scientist reproducing some photoelectric effect experiments
shines a light on a metal electrode, but doesn't...
asked 54 minutes ago -
In a study designed to test the effectiveness of magnets for
treating back pain, 35 patients...
asked 1 hour ago