A carbon steel coil spring has a mean diameter of 60 mm and is formed of...
A carbon steel coil spring has a mean diameter of 60 mm and is formed of 12 mm bar. It is subjected to a continuously alternating load between a maximum of 7000 N and a minimum of 4500 N. If the torsional yield point of the material is 700 MN/m2 and the endurance limit due to released loading is 300 MN/m2 , determine the factor of
safety under which the spring is operating from both the standpoint of endurance and yield.
Homework Answers
Add Answer to:
A carbon steel coil spring has a mean diameter of 60 mm and is
formed of...
A close-coiled helical spring has a mean coil diameter 120 mm. A load of 4 kN...
A close-coiled helical spring has a mean coil diameter 120 mm. A load of 4 kN causes a deflection of 50 mm and a maximum stress of 500 MPa. Calculate 4.1. a) The wire diameter b) The number of coils c) The energy absorbed when subjected to the maximum load d) The spring stiffness 4.2. By use of a clearly labelled neat sketch, show that the deflection in a close-coiled 12] where Wis ; where W is the axial load...
QUESTION 1 A compression coil spring made of an alloy steel is having the following specifications:-...
QUESTION 1 A compression coil spring made of an alloy steel is having the following specifications:- Mean diameter of coil = 50 mm; Wire diameter = 5 mm; Number of active coils = 20; If the spring is subjected to an axial load of 164 N. Calculate the maximum shear stress (Neglect the curvature effect) to which the spring material is subjected. (units of MPa).
A low carbon steel shaft is designed to have a diameter of 30 mm. It is...
A low carbon steel shaft is designed to have a diameter of 30 mm. It is to be subjected to an axial load (P-30 kN), a moment (M-200 N-m), and a torque (T-300 N-m). Assume the yield stress for the steel is (280 MPa), the Poisson's ratio is (v= 0.29), and the safety factor is (1-1). Calculate the margin of safety using the following failure theories. a.) Rankine Criteria (Maximum Principal Stress) b.) Tresca Criteria (Maximum Shear Stress) c.) Saint...
2. A h elical compression spring is made of 302 stainless steel wire. The outside coil...
2. A h elical compression spring is made of 302 stainless steel wire. The outside coil diameter of the spring 1S 33.2 mm. The wire diameter is 2.8 mm. The ends are plain and ground, and there are total of 8.5 turns. Determine the deflection of the spring when it is subjected to a compression force of 10 N. In this condition, will the stress generated in the spring be beyond the maximum allowable torsional stress? (30 points)
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends...
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
1. A closely coiled helical spring made of 15 mm diameter steel wire has 15 coils...
1. A closely coiled helical spring made of 15 mm diameter steel
wire has 15 coils of 110 mm mean diameter. The spring is subjected
to an axial load of 180 N. Calculate the maximum shear stress
induced in the spring. Assume modulus of rigidity is 78 GPa.
2. A solid circular bar ABC consists of two segments, as shown
in the figure. One segment has diameter d1= 65 mm and
length L1 = 1.54 m; the other segment has...
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yie...
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yield stress of 240 MPa. +F 200 mm Fig. Q5 (a) If a tensile axial force of 1MN is applied to the end plate, show that the maximum internal pressure that can be applied before the cylinder yields according to the Tresca criterion is 16.2...
P.1.9. A bar of mild steel has a diameter of 75 mm and is placed inside...
P.1.9. A bar of mild steel has a diameter of 75 mm and is placed inside a hollow aluminum cylinder of internal diameter 75 mm and external diameter 100 mm; both bar and cylinder are the same length. The resulting composite bar is subjected to an axial compressive load of 1000 KN. If the bar and cylinder contract by the same amount, calculate the stress in each. The temperature of the compressed composite bar is then reduced by 150°C but...
spring-2010 5. (a) A steel wire of diameter 0.60 mm and length 1.5 m. support A...
spring-2010 5. (a) A steel wire of diameter 0.60 mm and length 1.5 m. support A 5.0-kg mass. How much will the wire stretch under this load??Ystee-2x 1011 N/m2]
1. A helical compression spring has the following characteristics Wire diameter Outside diameter ...
Please answer if you are sure, thank you
1. A helical compression spring has the following characteristics Wire diameter Outside diameter Fmi 15.5 mm 15 N 100 N 115 N 25 mm maz End Treatment squared and ground Modulus of Rigidity80e9 N/m2 Note: Δ is the difference in deflection under the loads Fmin and Frnaz. Be sure to sketch the spring in its various states to assist in answering the following questions. (a) Find the spring constant, k. Be sure...
A close-coiled helical spring has a mean coil diameter 120 mm. A load of 4 kN causes a deflection of 50 mm and a maximum stress of 500 MPa. Calculate 4.1. a) The wire diameter b) The number of coils c) The energy absorbed when subjected to the maximum load d) The spring stiffness 4.2. By use of a clearly labelled neat sketch, show that the deflection in a close-coiled 12] where Wis ; where W is the axial load...
QUESTION 1 A compression coil spring made of an alloy steel is having the following specifications:- Mean diameter of coil = 50 mm; Wire diameter = 5 mm; Number of active coils = 20; If the spring is subjected to an axial load of 164 N. Calculate the maximum shear stress (Neglect the curvature effect) to which the spring material is subjected. (units of MPa).
A low carbon steel shaft is designed to have a diameter of 30 mm. It is to be subjected to an axial load (P-30 kN), a moment (M-200 N-m), and a torque (T-300 N-m). Assume the yield stress for the steel is (280 MPa), the Poisson's ratio is (v= 0.29), and the safety factor is (1-1). Calculate the margin of safety using the following failure theories. a.) Rankine Criteria (Maximum Principal Stress) b.) Tresca Criteria (Maximum Shear Stress) c.) Saint...
2. A h elical compression spring is made of 302 stainless steel wire. The outside coil diameter of the spring 1S 33.2 mm. The wire diameter is 2.8 mm. The ends are plain and ground, and there are total of 8.5 turns. Determine the deflection of the spring when it is subjected to a compression force of 10 N. In this condition, will the stress generated in the spring be beyond the maximum allowable torsional stress? (30 points)
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
1. A closely coiled helical spring made of 15 mm diameter steel
wire has 15 coils of 110 mm mean diameter. The spring is subjected
to an axial load of 180 N. Calculate the maximum shear stress
induced in the spring. Assume modulus of rigidity is 78 GPa.
2. A solid circular bar ABC consists of two segments, as shown
in the figure. One segment has diameter d1= 65 mm and
length L1 = 1.54 m; the other segment has...
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yield stress of 240 MPa. +F 200 mm Fig. Q5 (a) If a tensile axial force of 1MN is applied to the end plate, show that the maximum internal pressure that can be applied before the cylinder yields according to the Tresca criterion is 16.2...
P.1.9. A bar of mild steel has a diameter of 75 mm and is placed inside a hollow aluminum cylinder of internal diameter 75 mm and external diameter 100 mm; both bar and cylinder are the same length. The resulting composite bar is subjected to an axial compressive load of 1000 KN. If the bar and cylinder contract by the same amount, calculate the stress in each. The temperature of the compressed composite bar is then reduced by 150°C but...
spring-2010 5. (a) A steel wire of diameter 0.60 mm and length 1.5 m. support A 5.0-kg mass. How much will the wire stretch under this load??Ystee-2x 1011 N/m2]
Please answer if you are sure, thank you
1. A helical compression spring has the following characteristics Wire diameter Outside diameter Fmi 15.5 mm 15 N 100 N 115 N 25 mm maz End Treatment squared and ground Modulus of Rigidity80e9 N/m2 Note: Δ is the difference in deflection under the loads Fmin and Frnaz. Be sure to sketch the spring in its various states to assist in answering the following questions. (a) Find the spring constant, k. Be sure...
Most questions answered within 3 hours.
-
Computer Programming II CS141(Java)
Mention the appropriate relationship between following
classes:
HOD–StaffMember
Car–Ferrari
Student-Address
BankAccount–FixedAccount
House-Building...
asked 33 minutes ago -
Assume one of your finals has 50 questions on it, and
lucky for you, it's all...
asked 1 hour ago -
Rice Products in Bangladesh
Business behavior is derived in large part from the basic cultural
environment...
asked 3 hours ago -
The following base sequence is found for a mRNA fragment from
wild-type E. coli: 5'- UAUCAGUAGAUAAUGUAACC-3'...
asked 3 hours ago -
For this exercise, round all regression parameters to three
decimal places.
One of the two tables...
asked 3 hours ago -
What is the 5% level of significance for mean = 3.60, standard
deviation = 0.94, and...
asked 3 hours ago -
Prior to beginning work on this discussion, please read the
article by Hayley Peterson, 15 Companies...
asked 4 hours ago -
Which pair of aqueous solutions, when mixed, will form a
precipitate?
A) NaNO3 and AgC2H3O2
B)...
asked 4 hours ago -
1-Write an algorithm to get two numbers from the user (as
inputs) and calculate the sum...
asked 8 hours ago -
Define white-collar crime. What is the difference between
offender and offense-based definitions of white-collar crime? What...
asked 8 hours ago -
Consider a reaction which is 1st order with respect to A and 1st
order with respect...
asked 8 hours ago -
c++
The length of the hypotenuse of a right-angled triangle is the
square root of the...
asked 9 hours ago