What is the name of the device that uses induction to change voltage values in an AC circuit?
A) A transformer
B) A rectifier
C) An amplifier
D) A voltage modulator
E) An AC generator
Answer is A) Transformer
Since transformer uses faradays law of electromagnetic induction to induce voltage in the secondary side ,that voltage depends in number of turns in primary and secondary i.e secondary voltage is given by
VSecondary =Vprimary *(Nsecondary/Nprimary)
What is the name of the device that uses induction to change voltage values in an...
1) What component in a power supply converts ac line voltage to dc voltage? a. Transformer b. rectifier diode c. resistor d. capacitor 2) A circuit that provides an entirely positive or negative output voltage when an ac input voltage is applied is called a a. rectifier b. inverter c. filter capacitor d. zener diode 3) A control voltage or current is the a. power factor b. bias c. ground d. load 4) When the voltage at the op amp's...
answer all EEL 4220 Questions- AC Machines 1.) What is a balanced 30 system? 2.) What are advantages of 30? 3.) Explain why it is true that without the transformer, it would simply not be possible to use electric power in many of the ways it is used today. 4.) Explain how a transformer is able to change one ac voltage level to another voltage level and why the actual power supplied is not affected. 5.) What is a practical...
part g Q4. Most electronic systems need a dc voltage to work properly. The AC-to-DC power supply system is including a transformer, a rectifier and a capacitor input filter. The AC input voltage is 110 Vrms at 60 Hz. (a) Draw the full wave bridge rectifier circuit with transformer which steps down voltage to safer and lower levels that are more suitable for use with diodes (b) Show how the capacitor input filter connects to the rectifier output in the...
Figure 2 shows a power supply circuit comprising a transformer coupling the mains voltage on the left to the full-wave rectifier circuit on the right. It is given that the mains voltage (Vmains) is 230 V RMS, the mains frequency (fin) is 50 Hz, the transformer T1 has a ratio of 9:1, the load resistance (RL) is 1 k. and the capacitance of the capacitor (C) is 470 uF. a. Calculate the following: 1. the transformer AC output RMS voltage...
voltage f an npn be? What and Ao becolle ned device in (c) is operated at 10 μΑ, find produce the st and highest values of A,? What are these values? (d) If the redesigned lor, g,1%, and Ao. Which designs and operating conditions Figure P7 39 cases, if WIL is held at the same value 7.40 The NMOS trans ricated in pendix K erated at l is made 10 times larger, what gains result? 36 Using a CMOS technology...
30. The Hall-effect generator is constructed of a. N material 31. What three factors determine voltage amplitude produced by a Hall generator? a. Size of Hall generator b. Polarity of voltage applied c. Magnetic field strength b. P material (select all) d. Magnitude of current applied by source e. Temperature of Hall generator 32. What are two methods used to increase output signal from a Hall generator? use a diode across device b. use of concentrators (tuning) a. c. increase...
4. Design a npn BJT C-E amplifier circuit for the following specifications and given values: Voltage Gain Input resistance Load resistance Supply voltage Av = -60 Ri = 5k92 RL = 6k2 Vcc= 16V Assume Re is fully bypassed. The input source internal resistance Rs = 0.12. B=120 and VBE= 0.65V. Draw the actual circuit and its ac equivalent circuit
please help Question 1 Consider the following circuit, where the reverse saturation current (Is) is the same for each diode. D2 o Vo Di Vi WWW R 32 23 a. b. Determine an algebraic expression for V1, for a given Vo, and Is. Given an Is of 40 FA and R1 = 3.3 kl , determine the Vi that produces an output voltage (V.) of 0.625 V. C. Recalculate question-b if Is were to be a thousand times greater at...
your name here and on the back: In the given circuit 11-10mA, B- po 100, V2-15V and the capacitors are very large a) (2) Find lco b) (2) Find Vcro c) (2) Draw the AC midband model for the circuit C1 V2 CEO- R2 showing all component values. d) (2) What is the voltage gain of this amplifier? e (2) What load does VI see? V1 C2 0
For the inductive plethysmograph circuit shown, the inductive chest band and the 1 kohm resistor acts as a low pass filter. The Vosc is a signal generator tuned to 100022.4 Hz and 1 Vpp. a. If the inductance of the band was 1.59 mH, what is the corner frequency of the filter in Hz? b. What is the voltage output at point B in Vpp? c. When the person did inhalation the inductance increased to 3.18 mH. What is the...