help with the following problem please Proceed to design a digital circuit in which you want...
help with the following problem please
Proceed to design a digital circuit in which you want to control
two filling water pumps from a well to a reservoir. The system has
4 different sensors:
1. T1: Pump temperature 1
2. T2: Pump temperature 2
3. c: Minimum water level in the tank
4. d: Maximum water level in the tank
The system must operate taking into account the following
conditions:
A) If the water level of the tank is between sensor c and d only
pump 1 shall be operating, except that the temperature sensor
exceeds its limit, in this case it will enter into the function of
pump 2. This temperature limit on the pump shall be determined by
the activation of the pump sensor 1.
B) If the water level is below c and d, then both water pumps will
come into operation.
C) If a fault occurs in the water level sensors, such a case if the
d sensor is activated without the c sensor has been activated, then
both pumps must be deactivated for malfunction in the system.
D) The T1 and T2 temperature sensors shall determine the operation
of the pump, when the temperature sensor is activated, they must
deactivate the respective pump.
Homework Answers
Add Answer to:
help with the following problem please
Proceed to design a digital circuit in which you want...
just need the truth tables sop and circuits CET 363 Digital Circuits Design Project Liquid storage...
just need the truth tables sop and circuits
CET 363 Digital Circuits Design Project Liquid storage tank control unit In this projact you will design the control unit for a liquid storage tank. The control unit monitors temperature and liquid levels. The unit will maintain the appropriate liquid level by controlling input and output valves. The control unit also controls a heater to maintain the correct temperature range. Finaly, an alarm is activated if the liquid is too hot or...
5. You have been asked to develop a system to mix and bottle orange juice from concentrate. (5 po...
5. You have been asked to develop a system to mix and bottle orange juice from concentrate. (5 points) HINT: Select a PLC with 6 outputs. a. Low level detectors in the water 1) and concentrate (12) tanks prevent operating the water (Q1) and concentrate (Q2) pumps. b. The orange juice tank has a high level detector (14) which stops the pumps in the water and concentrate tanks. c. The conveyor belt motor (Q4) is initiated by a start (16)...
You have been asked to develop a system to mix and bottle orange juice from concentrate....
You have been asked to develop a system to mix and bottle orange juice from concentrate. a. Low level detectors in the water (I1) and concentrate (I2) tanks prevent operating the water (Q1) and concentrate (Q2) pumps. b. The orange juice tank has a high level detector (I4) which stops the pumps in the water and concentrate tanks. c. The conveyor belt motor (Q4) is initiated by a start (I6) and stop (I7) button. d. When a bottle is detected...
you can skip task 1 (3) because its a code in matlab. Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to...
you can skip task 1 (3) because its a code in
matlab.
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter ofthe pipe is equal to 30 cm water is to be pumped...
(b) Figure Q3 shows a design of a plumbing system to be used in a new building. Water at 20°C is ...
(b) Figure Q3 shows a design of a plumbing system to be used in a new building. Water at 20°C is free to be pumped from reservoir A to another reservoir B at a higher elevation through two 30 m long pipes connected in parallel on a common elevation level. The difference between the water surface elevations is 10 m. The pipes are made of commercial brass and the diameters of the two pipes are 4 cm and 8 cm....
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through...
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter of the pipe is equal to 30 cm. Water is to be pumped by a 72% efficient motor-pump combination that draws 33 A of...
Project-Design Problem: A family of water pumps produced by a given pump manufacturer have performance and...
Project-Design Problem: A family of water pumps produced by a given pump manufacturer have performance and efficiency curves that can be characterized by the following dimensionless equations: Pump head 6 = 6.04-1616 where and 5 nD Pump efficiency n = 705-91,5006 where n = (power to water) / (elect power input) In the above equations, is the dimensionless pump head and is the dimensionless volumetric flow rate. h, is the pump head, n is the pump shaft/impeller rotation rate, and...
1. You are designing a pumping station and have been asked to size and select a...
1. You are designing a pumping station and have been asked to size and select a pump from 2 models. The system step is as follows: the discharge line is a 21-inch diameter PVC pipe with an assumed constant friction factor of f 0.014. The length of the piping is 2300 ft with an elevation gain of 40 ft and an exit loss (K-1.0).. The pump station is located near sea level and the temperature of the flow stream is...
x2 AT 2. Fuel Tanks divided into compartments or baffles installed in them helps a. as...
x2 AT 2. Fuel Tanks divided into compartments or baffles installed in them helps a. as a failsafe system to avoid the fuel from leaking b. to keep a reserve for further flight in case the pump fails c. to keep the fuel from surging back and forth as aircraft changes its attitude in flight. d. none of the mentioned. 3. What does integral fuel tank mean? a. The tank is part of the structure with seams and joints sealed...
The following diagram illustrates a simple steam power plant. A 10kg/s flow of liquid water at...
The following diagram illustrates a simple steam power plant. A
10kg/s flow of liquid water at T1=25°C enters the pump at a
pressure of P1=100kPa and is then pumped to a pressure of P2=2MPa.
The boiler then heats the water at constant pressure to produce
superheated vapour at T3=450°C. The steam is then expanded in the
turbine to a final pressure of P4=100kPa. The turbine and pump are
well insulated and may be considered reversible.
a) Find the turbine exit...
just need the truth tables sop and circuits
CET 363 Digital Circuits Design Project Liquid storage tank control unit In this projact you will design the control unit for a liquid storage tank. The control unit monitors temperature and liquid levels. The unit will maintain the appropriate liquid level by controlling input and output valves. The control unit also controls a heater to maintain the correct temperature range. Finaly, an alarm is activated if the liquid is too hot or...
5. You have been asked to develop a system to mix and bottle orange juice from concentrate. (5 points) HINT: Select a PLC with 6 outputs. a. Low level detectors in the water 1) and concentrate (12) tanks prevent operating the water (Q1) and concentrate (Q2) pumps. b. The orange juice tank has a high level detector (14) which stops the pumps in the water and concentrate tanks. c. The conveyor belt motor (Q4) is initiated by a start (16)...
you can skip task 1 (3) because its a code in
matlab.
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter ofthe pipe is equal to 30 cm water is to be pumped...
(b) Figure Q3 shows a design of a plumbing system to be used in a new building. Water at 20°C is free to be pumped from reservoir A to another reservoir B at a higher elevation through two 30 m long pipes connected in parallel on a common elevation level. The difference between the water surface elevations is 10 m. The pipes are made of commercial brass and the diameters of the two pipes are 4 cm and 8 cm....
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter of the pipe is equal to 30 cm. Water is to be pumped by a 72% efficient motor-pump combination that draws 33 A of...
Project-Design Problem: A family of water pumps produced by a given pump manufacturer have performance and efficiency curves that can be characterized by the following dimensionless equations: Pump head 6 = 6.04-1616 where and 5 nD Pump efficiency n = 705-91,5006 where n = (power to water) / (elect power input) In the above equations, is the dimensionless pump head and is the dimensionless volumetric flow rate. h, is the pump head, n is the pump shaft/impeller rotation rate, and...
1. You are designing a pumping station and have been asked to size and select a pump from 2 models. The system step is as follows: the discharge line is a 21-inch diameter PVC pipe with an assumed constant friction factor of f 0.014. The length of the piping is 2300 ft with an elevation gain of 40 ft and an exit loss (K-1.0).. The pump station is located near sea level and the temperature of the flow stream is...
x2 AT 2. Fuel Tanks divided into compartments or baffles installed in them helps a. as a failsafe system to avoid the fuel from leaking b. to keep a reserve for further flight in case the pump fails c. to keep the fuel from surging back and forth as aircraft changes its attitude in flight. d. none of the mentioned. 3. What does integral fuel tank mean? a. The tank is part of the structure with seams and joints sealed...
The following diagram illustrates a simple steam power plant. A
10kg/s flow of liquid water at T1=25°C enters the pump at a
pressure of P1=100kPa and is then pumped to a pressure of P2=2MPa.
The boiler then heats the water at constant pressure to produce
superheated vapour at T3=450°C. The steam is then expanded in the
turbine to a final pressure of P4=100kPa. The turbine and pump are
well insulated and may be considered reversible.
a) Find the turbine exit...
Most questions answered within 3 hours.
-
The three key cash-related activities of a firm are
operational activities, non-current activities and financing
activities....
asked 2 hours ago -
what statement accurately depicts the similarities in
requirements between payroll and human resources function
asked 3 hours ago -
Calculate the volume integral of the function T=z^2 over the
tetrahedron with corners (0,0,0), (1,0,0), (0,1,0),...
asked 5 hours ago -
I propose to you a game. You roll 2 dice. If the sum of the
numbers...
asked 6 hours ago -
Select the most likely lattice types for each of the following
salts: (a) BeF2; (b) CaO;...
asked 6 hours ago -
a
ball is thrown downward with velocity of 10m/s. calculate the final
velocity if it reaches...
asked 7 hours ago -
How many grams of ice at -15°C must be added to 705 grams of
water that...
asked 8 hours ago -
2. Balance sheet
The balance sheet provides a snapshot of the financial condition
of a company....
asked 9 hours ago -
In week 1 of the chemical equilibrium experiment, you and your
lab team will create a...
asked 9 hours ago -
Identify and describe five (5) characteristics of a good KM
measurement system. Be sure to include...
asked 9 hours ago -
What are at least five (5) workplace wellness best practices for
a successful wellness program? Explain...
asked 9 hours ago -
A pharmaceutical company is testing a new drug. Of the 110
people that received the drug,...
asked 10 hours ago