answer asap and show work: Design a passive Band-Pass filter that has the following characteristics: 1....
answer asap and show work:
Design a passive Band-Pass filter that has the following characteristics:
1. Center frequency of 10kHz, with a bandwidth of 500 Hz.
2. The current through the circuit should be less than 10mA for a 1V sinusoidal input signal.
Homework Answers
Hope this helps.
Do give a like if you like the answer. It'll encourage me to write more quality answers.
Add Answer to:
answer asap and show work:
Design a passive Band-Pass filter that has the following
characteristics:
1....
C V. Figure 2 A band-pass filter circuit This is the transfer function of a band-pass...
C V. Figure 2 A band-pass filter circuit This is the transfer function of a band-pass filter having R = R2 //R Center frequency, a[ 1/R' R C12 radians Bandwidth B2(R, C) radians Maximum Gain Ag- R/2R Band-Pass Filter Design Design a band-pass filter to obtain f-160 Hz, B-16 Hz and o- 10. Supply voltages of +20 and -20 Volts are available. Laboratory Measurements and Results . By applying sinusoidal voltage at the input and by varying its frequency, obtain...
Which of the following are design steps for making a notch filter? Select all correct answers....
Which of the following are design steps for making a notch filter? Select all correct answers. Group of answer choices Make a Band Pass filter with twice the resonat frequency and bandwidth you need for the notch filter. Using an Non-Inverting adder circuit mix the output of the designed Band Pass filter with the orginal input signal. Using an Inverting adder circuit mix the output of the designed Band Pass filter with the orginal input signal. Using an Inverting adder...
Consider the filter shown in Figure P1 a) Show that the circuit behaves as a band-pass...
Consider the filter shown in Figure P1 a) Show that the circuit behaves as a band-pass fiter. (Hint: Find the transfer for this circuit and show that it has the same form as the transfer function for a band-pass filter.) b) Find the center frequency, bandwidth and gain for this band-pass filter c) Find the cutoff frequencies and the quality factor for this band-pass filter. 10 u.F 5 k2 50mF 16 400 (2 Figure P1
A) Design a low-pass filter using the given circuitry with a cut-off value of 1 kHz and plot the ...
a) Design a low-pass filter using the given circuitry with a cut-off value of 1 kHz and plot the frequency response curve on the given axes 1.0 0.7 0.5 in out 0.0 101 102 103 104 10s Hz b) Design a band-pass filter using the given circuitry with a bandwidth of 500 Hz and a lower cut-off value of 100 Hz, and draw the frequency response curve. Keep all resistors at the same value (i.e. Ri-R-R3-R4). 1.0 0.7 0.5 0.0...
BPF Filter Bandpass Filter The following circuit acts as a C This filter has a center...
BPF Filter Bandpass Filter The following circuit acts as a C This filter has a center (resonance) frequency at Hz. 27-VLC and a 3-dB bandwidth of BW = Hz. 2RC 3l f, and a passband for which the signal is This means that the filter has 0 dB gain at attenuated less than 3 dB centered approximately at f, from f,-BW2 to f.+BW/2 (this passband is not exactly centered at f, but its total width is BW) 3l8 Input Signal...
RC Circuit Design a passive, low-pass filter with corner frequency around 400 Hz and input impedance...
RC Circuit
Design a passive, low-pass filter with corner frequency around 400 Hz and input impedance of at least 1k2. Ģive the component values and compute the magnitude of the output impedance at 100 Hz.
For the Multi Feedback Topology Band-pass Filter circuit shown in Figure 1 below, confirm the transfer...
For the Multi Feedback Topology Band-pass Filter circuit shown in Figure 1 below, confirm the transfer function H(s) given below 0 Figure 1: Multiple Feedback Topology Band-pass Filter (MFT BPF) Vo SR で 1 Ri R3 2R TR2C where the filter's parameters are o f: middle (center) frequency in Hz o Am: gain at middle frequency, fm, in V/V o B: bandwidth between half power frequencies in Hz o Q: quality factor. One of the nice features of this circuit...
Design a second order IIR Butterworth low pass digital filter with a cutoff frequency of 500...
Design a second order IIR Butterworth low pass digital filter with a cutoff frequency of 500 Hz and a sampling frequency of 10,000 Hz using bilinear transformation then find the following: The output (response) due to the following inputs: Sinusoidal signal with a frequency of 100Hz. Sinusoidal signal with a frequency of 500Hz. Sinusoidal signal with a frequency of 2000Hz. Repeat (a) above for a 6thorder Butterworth filter
Using the windowing functions discussed in class, design a low-pass FIR filter with a cutoff freq...
Using the windowing functions discussed in class, design a
low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum
stop band attenuation of 40 dB, and a transition width of 200Hz.
The sampling frequency is 10kHz.
1. Using the windowing functions discussed in class, design a low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum stop band attenuation of 40 dB, and a transition width of 200 Hz. The sampling frequency is 10 kHz 2....
Prob. 5 (a) Consider the FM signal with modulation index B 2 is passed through an ideal band-pass...
Prob. 5 (a) Consider the FM signal with modulation index B 2 is passed through an ideal band-pass filter (BPF) with mid-band frequency f and bandwidth 5f. where f is the carrier frequency and fmis the frequency of the baseband modulating signal (i) Sketch the spectrum of the BPF output. (ii) Determine the fraction of the power of the FM signal that is present at the output of the filter (b) Consider the FM signal given by фFM (t)-100 cos...
C V. Figure 2 A band-pass filter circuit This is the transfer function of a band-pass filter having R = R2 //R Center frequency, a[ 1/R' R C12 radians Bandwidth B2(R, C) radians Maximum Gain Ag- R/2R Band-Pass Filter Design Design a band-pass filter to obtain f-160 Hz, B-16 Hz and o- 10. Supply voltages of +20 and -20 Volts are available. Laboratory Measurements and Results . By applying sinusoidal voltage at the input and by varying its frequency, obtain...
Consider the filter shown in Figure P1 a) Show that the circuit behaves as a band-pass fiter. (Hint: Find the transfer for this circuit and show that it has the same form as the transfer function for a band-pass filter.) b) Find the center frequency, bandwidth and gain for this band-pass filter c) Find the cutoff frequencies and the quality factor for this band-pass filter. 10 u.F 5 k2 50mF 16 400 (2 Figure P1
a) Design a low-pass filter using the given circuitry with a cut-off value of 1 kHz and plot the frequency response curve on the given axes 1.0 0.7 0.5 in out 0.0 101 102 103 104 10s Hz b) Design a band-pass filter using the given circuitry with a bandwidth of 500 Hz and a lower cut-off value of 100 Hz, and draw the frequency response curve. Keep all resistors at the same value (i.e. Ri-R-R3-R4). 1.0 0.7 0.5 0.0...
BPF Filter Bandpass Filter The following circuit acts as a C This filter has a center (resonance) frequency at Hz. 27-VLC and a 3-dB bandwidth of BW = Hz. 2RC 3l f, and a passband for which the signal is This means that the filter has 0 dB gain at attenuated less than 3 dB centered approximately at f, from f,-BW2 to f.+BW/2 (this passband is not exactly centered at f, but its total width is BW) 3l8 Input Signal...
RC Circuit
Design a passive, low-pass filter with corner frequency around 400 Hz and input impedance of at least 1k2. Ģive the component values and compute the magnitude of the output impedance at 100 Hz.
For the Multi Feedback Topology Band-pass Filter circuit shown in Figure 1 below, confirm the transfer function H(s) given below 0 Figure 1: Multiple Feedback Topology Band-pass Filter (MFT BPF) Vo SR で 1 Ri R3 2R TR2C where the filter's parameters are o f: middle (center) frequency in Hz o Am: gain at middle frequency, fm, in V/V o B: bandwidth between half power frequencies in Hz o Q: quality factor. One of the nice features of this circuit...
Using the windowing functions discussed in class, design a
low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum
stop band attenuation of 40 dB, and a transition width of 200Hz.
The sampling frequency is 10kHz.
1. Using the windowing functions discussed in class, design a low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum stop band attenuation of 40 dB, and a transition width of 200 Hz. The sampling frequency is 10 kHz 2....
Prob. 5 (a) Consider the FM signal with modulation index B 2 is passed through an ideal band-pass filter (BPF) with mid-band frequency f and bandwidth 5f. where f is the carrier frequency and fmis the frequency of the baseband modulating signal (i) Sketch the spectrum of the BPF output. (ii) Determine the fraction of the power of the FM signal that is present at the output of the filter (b) Consider the FM signal given by фFM (t)-100 cos...
Most questions answered within 3 hours.
-
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 1 hour ago -
Please answer what the maximum and minimum force is, and the
angle on the ion is...
asked 1 hour ago -
implement a program that reads a number of rows and a symbol.
The program will draw...
asked 1 hour ago -
Assume that when adults with smartphones are randomly selected,
45% use them in meetings or classes....
asked 1 hour ago -
Determine the number of formula units of
Na2SO4 and moles of oxygen contained in 8.11
moles...
asked 1 hour ago -
Explain in steps on the following code
What would be the output when executed
using System;...
asked 1 hour ago -
Given the information in the table, which of the following
statements is CORRECT?
Stock A
Stock...
asked 1 hour ago -
Write MARIE assembly language programs that do the following:
Write a program that inputs an integer...
asked 1 hour ago -
Explain an understanding of services and protocols.
Explain the job of DNS.
Explain the three email...
asked 2 hours ago -
(As soon as possible) Balance each of the following equations
according to the half-reaction method:
H2O2(aq)...
asked 2 hours ago -
A thin rod with a mass of 3.5kg and a length L=1.5 m is oriented
horizontally....
asked 2 hours ago -
Inheritance pattern in BRCA 1
Describe the inheritance pattern of BRCA 1 Is it recessive or...
asked 2 hours ago