IC 74153 is a combination of two 4 to 1 MUX. The function given in the question has 4 bits A, B, C, and D, so at first, we need to convert 4 to 1 MUX to 8 to 1. In 4 bits A will be used as input and B, C and D will be used as a select line.
From the function given: F(A,B,C,D) = (0,1,2,3,4,5,7,8,12)
and Dont Care(d) = d(10,11)
So the implicit chart of the function is given below:
where D0 to D7 are the input of the MUX.
Circuit Diagram is given below:
Pin Diagram of select line A and B are 14 and 2 respectively.
Input A, B, C, and D will be connected to the inputs. Other than this we need to use NOT Gate and OR Gate.
Refer to the 74153 chip's function table and connection diagram. Implement the function below usi...
can you solve all of them
Q3) Implement the truth table given below using Output Inputs b a с 0 0 0 0 0 0 0 0 Don't care 0 0 0 1 0 0 Don't care 1 (a) A single 3-to-8 Decoder and any simple logic gate (e.g. AND/OR/INV) (b) A single 8-to-1 Multiplexer and any simple logic gate (e.g. AND/OR/INV) (c) A single 4-to-1 Multiplexer and any simple logic gate (e.g. AND/OR/INV)
Question #6 6 points Implement the function from the truth table below (X, Y, Z are inputs. F is the output) using a) An 8:1 multiplexer b) A 4:1 multiplexer and one inverter c) A 2:1 multiplexer and two other logic gates Y z F 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 1 -
(a) The truth table below shows a certain function
F(P,Q,R,S).
Implement the function F using an 8:1 multiplexer, without any
other logic gate. Only the constants 0 and 1, and the literals (but
not their complements) are available.
Fill in the inputs in the multiplexer diagram.
(b). Implement the function F
using a 24 decoder and a 4:1 multiplexer, and at most one logic
gate. Only the constants 0 and 1, and the literals (but not their
complements) are available....
A combination circuit is specified by the following Boolean functions listed below. h(a, b, c) = b,c' + a'c Implement the circuit with a 3x8 decoder. Provide truth table and drawing the logic/circuit diagram. Use the block diagram for the decoder provided in Figure A4 in supplements. Please label the inputs and outputs clearly. Note: use single 3x8 decoder Question 2 (15 points] A priority encoder is an encoder circuit that includes the Truth Table of a priority function. The...
Could you please read 7483 data sheet and then answer number
e
7383 Data Sheet
5483A 4-Bit Binary Full Adder with Fast Carry General Description The '83A high speed 4-bit binary full adders with internal carry lookahead accept two 4-bit binary words (Ao-A3, Bo- B3) and a Carry input (Co). They generate the binary Sum outputs (So-S3) and the Carry output (C4) from the most significant bit. They operate with either HIGH or active LOW operands (positive or negative logic)....
Just need the code for the
random counter,Thanks
Objective: In this lab, we will learn how we can design sequential circuits using behavioral modelling, and implementing the design in FPGA. Problem: Design a random counter with the following counting sequence: Counting Sequence: 04 2 9 168573 Design Description: The counter has one clock (Clock), one reset (Reset), and one move left or right control signal (L/R) as input. The counter also has one 4bit output O and one 2bit output...