End out the audtpust eunud (I) and oudenst nesistane of the followin ciroud 3 100 VA 75A Hene, "A...
VA is the early voltage. i dont think that id necessary to solve the question though. + 3 V 22. 10 k 2 In the emitter follower shown, the signal source is directly connected to the base. The de component of Us is zero. The transistor has B = 100 and VA = 125 V. What is the output resistance of the follower? Find the gain vo/Us with no load and with a load of 1 k 2. With the...
My answer may or may not be right. Ignore it. For the multistage amplifier below assume, p-100, VA-72V, VT-0.026, VBE(on)-0.7 V V+= 15 V Rc6 R-12k R-12k Vos 35.75k 06 ei 02 REs REF 6.33k 1C3 0s ˇ-쁘-15 v 04 0s V-15 V What is the output resistance Ro of the current source that is biasing the differential pair differential pair and the value of TEs (emitter current of Q6) Ro-144k, IE6-2 mA Ro-144k, IE6-1 mA R 144k, I 1.2...
Problem 2. T Vcc=10v 4R3 Rc=5k12 Ko Yout C=0 Q(8=100, VBE=0.7, V=25mV, VA ) IRB IC=0 RB Fig. 3 In the common emitter amplifier shown in Fig. 3. a) Neglecting the base current (18 = 0), determine Rei and Rez to set Ice = 1 mA and the small-signal voltage gain |Apl= |Vout/Vin) = 20. [45 pt.) b) Base on the Ico given and ß = 100, choose Rp so that lg is 5% of IRB (15 pt.)
3. In Figure 3 on page 5, the DC operating point for the PNP transistor Qi is Ic = 0.33 mA and Vec = 2.4 V, and the DC operating point for the NMOS transistor Mi is ID = 2.81 mA and Vos = 2.92 V. Qı has B = 100, VA = 85 V at room temperature and Mi has Kn= 1 mA/V2, Vin= 1 V and 2 = 0.02 V-1. Assume that the capacitors have infinite values, and...
I need asnwer for both questions 3- A capacitor of 10 uF is charged to 20 V and is connected through of 3.3 kQ. At t- 0, the switch closes and the capacitor begins to discharge. What is the voltage across the capacitor after 20 ms? an open switch to a resistor Vc= 5.95 V Vc 1.77 V Vc - 0 V I Vc= 10.91 V 8- An inductor of 220 mH is charged to 10 mA and is connected...
Question 4 0 out of 3 points Given Vab 100 Volts and I 20 Amps, find the conductance 2 out of 2 points
i dont undersrand how to calculate the values from measured data? 2. Turn on the DC power supply, measure its output voltage with DMM2 and record it as measured data Vs in Table 6. 3. Use DMM2 to measure the voltages V, V2.V. Va across R R. RR respectively. Use DMMI to measure the current Is (notice: Is=1= 12 + 1,-1). Record the measured values of I, and V., V2, V3. V4 in Table 6. 4. Turn off the DC...
Write a python nested for loop that prints out the following pattern 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33...
I have the answers here from the textbook but am having trouble figuring out how to set up equations. Any help is appreciated thanks! P 6.4-6 + Determine the node voltages for the circuit shown in Figure P 6.4-6. Answer: va = -0.75 V, Vb = 0 V, and Vc = -0.9375 V 10 k 40 k 20 k MMM- b 25 k W 12 v 340k 3 15k Figure P 6.4-6
Question 86 - 100: Look at the graph of function f(r) . A -5 -1 3 5 7 9 11 1--1 86. lim f(x) = 87. lim f() = 88. Is f(x) continuous at I = 1? 89. Is f(x) continuous at x = 0? 90. Is f(x) continuous at x = - 3 from the left hand side ? 91. limf() = 92. Does limf (x) exist ? 93. Is f(x) continuous at I = 8? 94. Is f()...