2) An aluminum specimen with a defect as shown having a thickness of 2 mm width 22 mm, the defect...

Question

Question

2) An aluminum specimen with a defect as shown having a thickness of 2 mm width 22 mm, the defect has a hole of 4.8S mm radiu

engineering Mechanical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

わma, Upper yicid port al culo んで G 200 UTS 6260 4.S7 6 NImm2 3s4.76

Add a comment

Answer 2

Similar Homework Help Questions

2) An aluminum specimen with a defect as shown having a thickness of 2 mm width 22 mm, the defect...

2) An aluminum specimen with a defect as shown having a thickness of 2 mm width 22 mm, the defect has a hole of 4.8S mm radius, the crack length is 12.5 mm from tip to tip the length of the specimen was 65 mm , this specimen is subjected to a tensile foree up to 6200 N, it fractured at Find the ultimate stress 2) An aluminum specimen with a defect as shown having a thickness of 2 mm...
Strength of material 2) An aluminum specimen with a defeet as shown having a thickness of 2 mm width 22 mm, the defeet has a hole of 4.S mm radius, the crack length is 12.5 mm from tip to tip the...

Strength of material 2) An aluminum specimen with a defeet as shown having a thickness of 2 mm width 22 mm, the defeet has a hole of 4.S mm radius, the crack length is 12.5 mm from tip to tip the length of the specimen was 65 mm , this specimen is subjected to a tensile fore up to 6200 N, it fractured at s4s0 Find the ultimate stress. 10 marks 2) An aluminum specimen with a defeet as shown...
3. A square rod of 500 mm long with a width of 10 mm is subjected...

3. A square rod of 500 mm long with a width of 10 mm is subjected to a load of 40000 N., The stress-strain behavior is shown in the Figure below. Based on the information, please answer the following questions: (Note: Pa = N/㎡, J = Nm) (a) Compute the applied stress (5 points). 70 Tensile strength 450 MPa (65.000 ps) -60 400 103 ps MPa 40厂 50 300 40 Yield strength30 250 MPa (36.000 ps) 200 100 20 10...

A PMMA plate with a 25 mm (width) x 6.5 mm (thickness) cross-section has a contained...

A PMMA plate with a 25 mm (width) x 6.5 mm (thickness) cross-section has a contained crack of length 2c = 0.5 mm in the center of the specimen. If the applied load (along the 2 length direction) is 1000 N, calculate the stress intensity factor. If the fracture toughness of PMMA, K1c = 1.15 MPa.m1/2, at what load (in N) does the crack propagate?
| A three point bending test was performed on an aluminum oxide specimen having a circular...

| A three point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 5,0mm; the specimen fractured at a load of 3000 N when the distance between the support points was 40mm. Another test is to be performed on a specimen of this same material, but one has a square cross section of 15 mm length on each edge. At what load would you expect this specimen to fracture if the support point...
please answer both the questions Question 2 A titanium tube 200mm diameter and 5mm wall thickness...

please answer both the questions Question 2 A titanium tube 200mm diameter and 5mm wall thickness is subjected to an internal pressure of 13.5MPa. The tube contains a longitudinal crack along its full length. Assuming that the tube can be approximated by a single edge notched plate subjected to a tensile stress equal to the hoop stress in the tube determine the crack length to cause failure. You may assume that the material fracture toughness is 55 MPavm. Please provide...

1.6 points) A tensile test specimen having a diameter of 10 mm and a gange length...

1.6 points) A tensile test specimen having a diameter of 10 mm and a gange length of 50 mm wa. tested to fracture. The stress-strain curve from the tension test is shown below. Labeling your points and showing the necessary steps, along with the corresponding calculations, find the following magnitudes: (a) Modulus of Elasticity, E = (b) Ultimate Strength = (e) Yield stress (0.2% offset method), (d) If the shear modulus of elasticity of the material is 28 GPa, determine...
5. A cylindrical specimen of aluminum having a diameter of 12.8 mm and a gauge length...

5. A cylindrical specimen of aluminum having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. Use the load-elongation characteristics tabulated below to complete parts (a) through (f). Use SI unit system. Load Length 0 7330 15,100 23,100 30,400 34,400 38,400 41,300 44,800 46,200 47,300 47,500 46,100 44,800 42,600 36,400 lb 0 1650 3,400 5,200 6,850 7,750 8,650 9,300 10,100 10,400 10,650 10,700 10,400 10,100 9,600 mim 50.800 50.851 50.902 50.952 51.003 51.054...
A thin film of aluminum has length 1 cm, width 1 mm and thickness 1000 angstroms....

A thin film of aluminum has length 1 cm, width 1 mm and thickness 1000 angstroms. A 50 mA current is flowing along the length of this film. What will be the Hall voltage developed across the width of this sample when a magnetic field of 1 tesla is applied perpendicular to the plane of the film? The carrier concentration in aluminum is 2 x 10"/cm'. Please give your answer in SI units.

2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and...

2. (70 pts) A cylindrical specimen of an alloy having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. The load-length data are recorded during the test and are tabulated below. After fracture, the diameter of the specimen near the fracture point was 9.5 mm. Load (N) 7,330 15,100 23,100 30,400 34,400 38,400 41,300 44.800 46,200 47,300 47,500 46,100 44,800 42,600 36,400 Length (mm) 50.800 50.851 50.902 50.952 51.003 51.054 51.308 51.816 52.832...

2) An aluminum specimen with a defect as shown having a thickness of 2 mm width 22 mm, the defect...

Homework Answers