Homework Answers
Add Answer to:
A 400:5 CT with a secondary resistance of 0.211 ohms is used as part of an over-current relay. Th...
A CT of ratio of 200:5 is used in a relaying application where the burden impedance...
A CT of ratio of 200:5 is used in a
relaying application where the burden impedance is 0.5 ohms. If the
pick-up current value is 5 A, what is the line current required to
trip the relay? Also what is the CT error? Hint: Calculate the
total secondary current using the graph (I_s=I_e+I_pc) then find
the line current using the CT ratio.
POWER SYSTEMS PROTECTION
A CT of ratio of 200:5 is used in a relaying application where the burden...
1. Calculate the VA output required from a current transformer of 5A rated secondary current when...
1. Calculate the VA output required from a current transformer of 5A rated secondary current when the burden consists of relays requiring 10VA at 5A plus a loop lead resistance of 0.8 ohms. 2. What output VA would be required from a current transformer of 1A rated secondary current for a burden of 10VA at 1A plus lead resistance as in part 1. 3. An earth fault relay has a burden of 1VA at setting and is set at 0.2A....
Problem #1 A multi-ratio current transformer with the following ratios (1200:5, 1000/5, and 800:5) high permeability...
Problem #1 A multi-ratio current transformer with the following ratios (1200:5, 1000/5, and 800:5) high permeability silicon steel has a cross sectional area of 3.5 square-inches and a secondary resistance winding of 0.29 Ohms. The maximum current for which the transformer will operate is 35kA at 60 Hz. The relay burden including the leads is 2.2 Ohms. Using the formula method determine if the CT will saturate at the three given rations (CT saturation density)
Please answer the following with all explanations Problem #3 A 1200/5, C400 CT is connected on the tap 1000/5. What is the maximum secondary burden that can be used and we can maintain rated accur...
Please answer the following with all explanations
Problem #3 A 1200/5, C400 CT is connected on the tap 1000/5. What is the maximum secondary burden that can be used and we can maintain rated accuracy at 20 times rated symmetrical secondary current?
Problem #3 A 1200/5, C400 CT is connected on the tap 1000/5. What is the maximum secondary burden that can be used and we can maintain rated accuracy at 20 times rated symmetrical secondary current?
The amount of available fault current at the service depends upon the ______. Method of banding...
The amount of available fault current at the service depends upon the ______. Method of banding Method of grounding Size and impendence of the service transformer Ampere rating of the overcurrent protection device The line current for a 240/120 volt, 3-phrase system, if each phase is balanced with a 3,000-VA load and the total load is 9,000 VA, is ______ amperes. 12.5 15 21.65 37.5 Given: A dwelling unit has 3,000 sq.ft. of habitable space with laundry facilities and bathrooms,...
32. A transformer is to be designed to increase the 30 kV-rms output of a generator...
32. A transformer is to be designed to increase the 30 kV-rms output of a generator to the transmission-line voltage of 345 kV-om. If the primary winding has 80 turns, how many turns must the secondary have? b. 70 c. 920 d. 9200 e 12 33. The primary winding of an electric train transformer has 400 turns and the Secondary has 50. If the input voltage is 120V(rms) what is the output voltage? a. 15 V (rms) b. 30 Vrms)...
B oth 100 Day PH262 Page 1 of 5 Lab #13 AC Circuits, Part 1 RC...
B oth 100 Day PH262 Page 1 of 5 Lab #13 AC Circuits, Part 1 RC & RL, Phase Measurements THEORY The rotating phase representation for series AC circuits should be familiar from textbook and lecture notes A brief outline of the essential points is provided here. If a series RLC circuit is connected across a source of om which is a sinusoidal function of time, then und all its derivatives will also be inside. Sonce all demits in a...
I need help to solve this questions about Generator Governor Droop and Transmission Line. A complete...
I
need help to solve this questions about Generator Governor Droop
and Transmission Line. A complete solutions with answers would be
great. Thank you
Generation Question 1 to 5 relate to the following grid connected generator. A governor-controlled, steam-driven 450 MW synchronous generator with 5% droop is synchronized to the 60 Hz grid and its load set-point adjusted to deliver 300 MW to the grid. Q1. (a) 000 What is the actual droop of the generating unit? 0.0225 Hz/MW (b)...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 an...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...
A CT of ratio of 200:5 is used in a
relaying application where the burden impedance is 0.5 ohms. If the
pick-up current value is 5 A, what is the line current required to
trip the relay? Also what is the CT error? Hint: Calculate the
total secondary current using the graph (I_s=I_e+I_pc) then find
the line current using the CT ratio.
POWER SYSTEMS PROTECTION
A CT of ratio of 200:5 is used in a relaying application where the burden...
Problem #1 A multi-ratio current transformer with the following ratios (1200:5, 1000/5, and 800:5) high permeability silicon steel has a cross sectional area of 3.5 square-inches and a secondary resistance winding of 0.29 Ohms. The maximum current for which the transformer will operate is 35kA at 60 Hz. The relay burden including the leads is 2.2 Ohms. Using the formula method determine if the CT will saturate at the three given rations (CT saturation density)
Please answer the following with all explanations
Problem #3 A 1200/5, C400 CT is connected on the tap 1000/5. What is the maximum secondary burden that can be used and we can maintain rated accuracy at 20 times rated symmetrical secondary current?
Problem #3 A 1200/5, C400 CT is connected on the tap 1000/5. What is the maximum secondary burden that can be used and we can maintain rated accuracy at 20 times rated symmetrical secondary current?
32. A transformer is to be designed to increase the 30 kV-rms output of a generator to the transmission-line voltage of 345 kV-om. If the primary winding has 80 turns, how many turns must the secondary have? b. 70 c. 920 d. 9200 e 12 33. The primary winding of an electric train transformer has 400 turns and the Secondary has 50. If the input voltage is 120V(rms) what is the output voltage? a. 15 V (rms) b. 30 Vrms)...
B oth 100 Day PH262 Page 1 of 5 Lab #13 AC Circuits, Part 1 RC & RL, Phase Measurements THEORY The rotating phase representation for series AC circuits should be familiar from textbook and lecture notes A brief outline of the essential points is provided here. If a series RLC circuit is connected across a source of om which is a sinusoidal function of time, then und all its derivatives will also be inside. Sonce all demits in a...
I
need help to solve this questions about Generator Governor Droop
and Transmission Line. A complete solutions with answers would be
great. Thank you
Generation Question 1 to 5 relate to the following grid connected generator. A governor-controlled, steam-driven 450 MW synchronous generator with 5% droop is synchronized to the 60 Hz grid and its load set-point adjusted to deliver 300 MW to the grid. Q1. (a) 000 What is the actual droop of the generating unit? 0.0225 Hz/MW (b)...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...
Most questions answered within 3 hours.
-
(a) A lightbulb has a resistance of 165 Ω when operating with a
potential difference of...
asked 4 minutes ago -
Questions
Submission Question 2: Stacks
Problem
Write a program that keeps track of where cars are...
asked 3 minutes ago -
Using α = 0.05, test if the mean weight change
is less than 0 if a...
asked 22 minutes ago -
JAVA
Lab -Lottery Calculator
IMPORTANT: This lab is best implemented using a loop structure.
If you...
asked 10 minutes ago -
A diver springs upward with an initial speed of 2.1 m/s from a
3.5-m board.
(a)...
asked 18 minutes ago -
In an isobaric compression process, the volume of steam is
reduced from 1 Mpa and 773...
asked 22 minutes ago -
blood glucose level for obese patient population have
a mean of 100 with a standard deviation...
asked 23 minutes ago -
Which of the following mutations is MOST likely to be
recessive?
A.
Deletion of a haplo-insufficient...
asked 27 minutes ago -
The U.S. Department of Transportation, National Highway Traffic
Safety Administration, reported that 77% of all fatally...
asked 39 minutes ago -
For 1 through 11, create an expression using the relational
operators, the logical operators, and variable...
asked 52 minutes ago -
Remove all recursion from the following grammar:
S -> Aa | Bb
A -> Aa |...
asked 45 minutes ago -
The production budget for Manner Company shows units to be
produced as follows: July, 550; August,...
asked 56 minutes ago