6.1.6. A process for making steel pipe is under control if the diameter of the pipe has mean 3.0 in. with standard deviation of no more than 0.0250 in. To check whether the process is under control,...
Question 2 (a)A new engineering software is being developed and claim that it is more than 98% compatible with the existing software. A sample of 200 engineering firms tested the new software and 180 of them agreed with the manufacturer. Test at 5% significance level whether the claim is true. (9 marks) (b) The noise level of a newly designed low noise transistor is normally distributed with mean and standard deviation 0.7 dB. The null hypothesis u-24dB is to be...
A control chart is used for monitoring a process meanl (X) that is normally distributed with a mean of μ and a standard deviation of σχ , and the sample size is n-5. А 3-sigma limit (μ ±30% ) is used as control limits. Two decision rules are given here. Rule 1: If one or more of the next seven samples yield values of the sample average that fall outside the control limits, conclude that the process is out of...
Product filling weights are normally distributed with a mean of 365 grams and a standard deviation of 19 grams. a. Compute the chart upper control limit and lower control limit for this process if samples of size 10, 20 and 30 are used (to 2 decimals). Use Table 19.3. For samples of size 10 UCL =| LCL For a sample size of 20 UCL = LCL For a sample size of 30 UCL = LCL = b. What happens to...
A gear has been designed to have a diameter of 3 inches. The standard deviation of the process is 0.3 inch. A control chart is shown. Each chart has horizontal lines drawn at the mean, μ, μ 2o, and at μ 3G. Determine if the process shown is in control or out of control. Explain Is the process in control or out of control? Select all that apply A. Out of control, because a point lies more than three standard...
SOLVE ONLY PART E has mean that has changecl tom 40 Assume that, when 1. There is a concern a voltage generator tested, the output χ will have mean μ with standard deviation σ2) HoY 40 vs. Ha:μ#40 a) (3pts) What kinds of values of 3 would lead to the rejection of the null hypothesis? In other words, what is the correct form of the rejection region (RR) ? SELECT A,B,C,D,E, or F: Answer A) Significantly larger than 40 B)...
Under normal operations the process that produces hypodermic needles produces needles whose diameter has a mean of 1.65mm and a standard deviation of 0.01mm. Every day, before operations begin, the machine is tested to make sure it is operating normally. The test consists of measuring the lengths of 5 needles coming off the machine. If the average diameter of the 5 needles is either greater than 1.655 or less than 1.645 the machine is shut down and inspected. a. When...
2. (2 True-False. Just say whether each statement is True or False – no need to justify your answer. 1. If the number of trials in the binomial distribution increases by 1 (and P equals .50), the probability of getting either of the most extreme possible outcomes (that is, 0 or N) is cut in half. 2. If the number of trials in the binomial distribution increases by 1 (and P does not equal .50), the probability of getting either of...
Drop down options for question a and be are: greater than less than or equal to Drop down options for part c are: type 1 or type 2 smaller or larger Consolidated Power, a large electric power utility, has just built a modern nuclear power plant. This plant discharges waste water that is allowed to flow into the Atlantic Ocean. The Environmental Protection Agency (EPA) has ordered that the waste water may not be excessively warm so that thermal pollution...
Q7) A hypothesis test is to be performed with a Null hypothesis and an alternative hypothesis , the population standard deviation is σ=3.0, the sample size is 30, and the significance level is α=0.025. What is a type I error? (1 mark) What is the chance of making a type I error in the above test? (1 mark) What is a Type II error? (1 mark) What value would the sample mean have to be greater than to reject Ho? (2 marks) It is...
QUESTION 8 [NOTE: The next 8 questions are all different parts of this question]. Before they can be marketed, all new medical devices must be approved by the Food and Drug Administration (FDA). A new device has a protective cover which needs to be removed easily. A similar device, already on the market, has a cover that requires an average force of 8 pounds to remove. The laboratory test data on a random sample of 9 of the new device...