R, Figure P7.49 .50 Figure P7.50 shows a current source realized using a current mirror with two matched transistors Q, and o, . Two equal resistances R, are inserted in the source leads to increase...
) The current-mirror circuit shown in Figure 3 utilizes pnp transistors having Isl 10-5A and/s2-2x10-5A for transistors Q1 and Q2 respectively and for both transistors a β 50, and |Val 10 V to source a current at Vo.It is required to design the circuit to provide an output current oflo= 1 mA at Vo = 2 V. What values of REF and R are needed? 0i 02 /REF lo ) The current-mirror circuit shown in Figure 3 utilizes pnp transistors...
For the differential amplifier shown in Figure 6: Assume well-matched transistors and = 100 for all transistors: a) Why it is important to use well-matched transistors in differential amplifier circuits? What is the potential influence of mismatched transistors on the performance of the differential amplifier? b) Determine the resistor values (R1, R2 and R3) such that the emitter coupled current IE = 0.5 mA and VC1 = 3 V. c) Draw the ac equivalent circuit for the single ended...
Beta = 100 10 V IRE R3 Fig. 1: A current source and mirror circuits using npn BJTS Design the current source and mirror circuit in Fig. 1 such that IREF = 10 mA (13%) nominally. Use supply of Vcc = 10 V, and use an average value for ß that you found in your previous experiments or that from the datasheet. Find the value of R, that satisfies the design requirements. In your pre- lab, perform the following: 1....
D 6.112 The MOSFET in the circuit of Fig. P6.112 has = 5 mA/V, and V, = 40 V. (a) Find the values of Rs,RD, and RG so that ID=0.4 mA, the largest possible value for R is used while a maximum signal swing at the drain of +0.8 V is possible, and the input resistance at the gate is 10 MS2. Neglect the Early effect. (b) Find the values of gm and r, at the bias point. (c) If...
(a) Determine R, R,, and R Assume gr1 (b) Determinei,,i,ふi4.is, is, and i,' alf in terms oft,. (Hini; Use the current-divider rule at the drain of Q,) (c) Determine v, t, and u, all in terms of v, (d) If บุ is a 5-mV peak sine wave and RJ,-20, sketch and clearly label the waveforms of v, U, and t, D 7.68 Design the double-cascode current source shown in Fig. P7.68 to provide 0.2 mA and the largest possible sig-...
D-17.121 The MOSFET in the circuit of Fig. P7.121 has V, 0.8 V, k,-5 mA/V", and V,-40 V (a) Find the values of Rş, Rp, and Ro so that Ip 0.4 mA, the largest possible value for Rp is used while a maximum signal swing at the drain of ±0.8 V is possible, and the input resistance at the gate is 10 M2. Neglect the Early effect. (b) Find the values of g and r at the bias point. (c)...
can you do 4.83 Ar- Q Sea 100 V, what does the gain become? age at the collector. (b) Replacing the transistor by its T model, da the small-signal equivalent circuit of the a plifier. Analyze the resulting circuit to dete mine the voltage gain t/ 04.81 Consider the CE amplifier circuit of Fig. 4.43(a). It is required to design the circuit (i.e., find values for I and Rc) to meet the following specifications: (a) R,5kn (b) the voltage gain...
Question 1: 7.33 +15V 1O MO R-200k 16n 7k MO 7.33 Figure P7.33 shows a discrete-circuit amplifier. The input signal is coupled to the gate through a very large capacitor (shown as infinite). The transistor source is connected to ground at signal frequencies via a very large capacitor (shown as infinite). The output voltage signal that develops at the drain is coupled to a load resistance via a very large capacitor (shown as infinite). All capacitors behave as short circuits...
Lab Preparation . Using DC analysis, and assuming that the transistors (QuEr and Q) are in the active mode, determine the value of RREF required for generating a copy current of 0.755 mA. Take the value of Vcc to be 8 V, and the value of VE in the active mode to be equal to 0.7V. Vee H Qur о RaI Figure 3 Single-stage amplifier biased by a simple current miror device 2. The circuit shown in Figure 3, is...
A common source amplifier circuit based on a single n-channel MOSFET is shown in Figure 4b. Assume that the transconductance gm-60 mS (equivalent to mA/ V) and drain source resistance, os, is so large it may be neglected. 0) Calculate the open circuit voltage gain Av Yout/ Vis. i) The amplifier has a load of 10 k2. Determine the current gain Va. = 12 V 150k 4k3 Vout Vin 200k GND = 0 V Figure 4b a) State the name...