Workshop Exercise 10. 0.4 A 20 13. On the part above, what is the flatness on the top surface with only the profile applied? 14. Apply a 0.1 flatness control to the top surface. 15. On the produc...

Question

Question

engineering Mechanical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

13) Given part surface is rectangular so that the flatness of the surface is 0.4

Means surface of the part be in between two planes which are separated by 0.4 distance.

め+ lane) tolerence OTR two ple恻ラftotneus

Add a comment

Answer 2

Similar Homework Help Questions

7. IT IS POSSIBLE THAT PERPENDICULARITY TO TWO DATUMS COULD HAVE BEEN SPECIFIED OWN ON THE PREVIO...

GD&T questions. Angularity, perpendicularity and parallelism. 7. IT IS POSSIBLE THAT PERPENDICULARITY TO TWO DATUMS COULD HAVE BEEN SPECIFIED OWN ON THE PREVIOUS EXAMPLE. SHOW AN EXAMPLE ON THE PART BELOW. SELECT YOUR O DATUMS 1.000 ±.003 2.886±.003 ! _ .61 7±.003 1 . 1 00±.003 400 ± .003 8. WHAT EFFECT WOULD TWO DATUMS HAVE ON PERPENDICULARITY? 9. ON THE PRODUCE PART BELOW, SHOW BY HAND SKETCH THE SPECIFIED PERPINDICULARITY TOLERANCE ZONE AND AN EXAMPLE OF HOW IT MAY...
Workshop Exercise 13.1 1. On the part below, apply postion controls to allow the holes to...

Workshop Exercise 13.1 1. On the part below, apply postion controls to allow the holes to move 0.4 side to side but only 0.1 in the up and down direction. Include references to datum features A, B, and C. - 3x Ø1503 10-01 2. On the part below, show the size and shape of the tolerance zones that were defined on the previous drawing. 3X Ø 150.3 + + 3. What is the perpendicularity tolerance for the 3 holes in...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated...

10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...

Chapter overview 1. Reasons for international trade Resources reasons Economic reasons Other reasons 2. Difference between...

Chapter overview 1. Reasons for international trade Resources reasons Economic reasons Other reasons 2. Difference between international trade and domestic trade More complex context More difficult and risky Higher management skills required 3. Basic concept s relating to international trade Visible trade & invisible trade Favorable trade & unfavorable trade General trade system & special trade system Volume of international trade & quantum of international trade Commodity composition of international trade Geographical composition of international trade Degree / ratio of...

Workshop Exercise 10. 0.4 A 20 13. On the part above, what is the flatness on the top surface with only the profile applied? 14. Apply a 0.1 flatness control to the top surface. 15. On the produc...

Homework Answers

Add Answer to:
Workshop Exercise 10. 0.4 A 20 13. On the part above, what is the flatness on the top surface with only the profile applied? 14. Apply a 0.1 flatness control to the top surface. 15. On the produc...

Post as a guest

Earn Coins

7. IT IS POSSIBLE THAT PERPENDICULARITY TO TWO DATUMS COULD HAVE BEEN SPECIFIED OWN ON THE PREVIO...

Workshop Exercise 13.1 1. On the part below, apply postion controls to allow the holes to...

10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated...

Chapter overview 1. Reasons for international trade Resources reasons Economic reasons Other reasons 2. Difference between...

Workshop Exercise 10. 0.4 A 20 13. On the part above, what is the flatness on the top surface with only the profile applied? 14. Apply a 0.1 flatness control to the top surface. 15. On the produc...

Homework Answers

Add Answer to: Workshop Exercise 10. 0.4 A 20 13. On the part above, what is the flatness on the top surface with only the profile applied? 14. Apply a 0.1 flatness control to the top surface. 15. On the produc...

Post as a guest

Earn Coins

7. IT IS POSSIBLE THAT PERPENDICULARITY TO TWO DATUMS COULD HAVE BEEN SPECIFIED OWN ON THE PREVIO...

Workshop Exercise 13.1 1. On the part below, apply postion controls to allow the holes to...

10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated...

Chapter overview 1. Reasons for international trade Resources reasons Economic reasons Other reasons 2. Difference between...

Add Answer to:
Workshop Exercise 10. 0.4 A 20 13. On the part above, what is the flatness on the top surface with only the profile applied? 14. Apply a 0.1 flatness control to the top surface. 15. On the produc...