this is the question and
i kniw hot to connect the circuit to the oscilloscope and signal
generator but im not sure what frequency values to set on the
signal generator and also i dont know how to get the gain from the
oscilloscope like am i supposed to get the peak to peak voltage and
divide it by the input voltage i have been given ? thanksHomework Answers
Add Answer to:
for the same black box circuit how do we measure the output voltage to calculate the gain because the input voltage is 1...
this is a practical question where you are given a black box and you connect it...
this is a practical question where you are given a black box and
you connect it on a breadboard to a power supply,oscilloscope and
signal generator. I got stuck on how to take the measurements as im
not sure what exact measurements to take to determine the bode
amplitude plot.
thanks
do
you know how to get the bode plot of a black box circuit. And what
measurements to take using an oscilloscope and signal generator to
get values for...
Part I: Black Box A Design your first black box adhering to the following specifications A. Input Signal to Black Box A 1. A 1 kHz cosine wave with amplitude of 1V. B. Output Signal from Black Box A...
Part I: Black Box A Design your first black box adhering to the following specifications A. Input Signal to Black Box A 1. A 1 kHz cosine wave with amplitude of 1V. B. Output Signal from Black Box A 1. A 1 kHz sine wave with amplitude of Hint: Use an ideal op-amp C. Explain your design process. What type of circuit did you design? Discuss D. Why did vou use an op-amp? Could another component be used instead? Why...
1. As a reference, observe the full amplitude range of the AC voltage, without limiting. R1...
1. As a reference, observe the full amplitude range of the AC voltage, without limiting. R1 330 0 f=1.0 kHz 3.0 k2 out Vap = 15.0 V Figure 1. AC Circuit without limiter Construct the circuit of Figure 1. Set the function generator for a sine wave with a frequency of about 1 kHz. Begin with the AC input voltage adjusted to its minimum value, approximately 0 V. Connect Channel 1 of the oscilloscope to observe the AC input voltag...
a) Calculate the theoretical Voltage Gain, Input resistance, and Output resistance for the circuit used in...
a) Calculate the theoretical Voltage Gain, Input resistance,
and Output resistance for the circuit used in this lab. Assume
Beta= 200 and that the signal generator has an output resistance of
50ohm
find Av? Rin? Rout?
vec 20.00 XSC1 (RB 470kg Tektronix C2 HE 100F 1 2N4124 CA M - 100F RE 32.2ko RL 1ko w
C- Amplifier: Consider figure 3. This circuit uses the JFET to amplify the input signal voltage F...
C- Amplifier: Consider figure 3. This circuit uses the JFET to amplify the input signal voltage First the dc operation must be set. Use equation 1 and your previous data to calculate the value of Vas required to give I-0.5 mA. Determine the source resistance Rs needed to set this bias. Set up the circuit of figure 3 with your calculated value of Rs. Measure Vo and Vs to determine if your operating conditions are correct. Apply an input voltage...
Objectives: To learn transient behavior of series RC circuits To observe of time constant and its...
Objectives: To learn transient behavior of series RC circuits To observe of time constant and its effect on charging process of capacitor using pulse waveforms Equipment: Oscilloscope Function generator Resistors (1 k) Capacitors (1 uF) Breadboard Pre-Lab Questions A pulse is a voltage or current that changes from one level to the other and back again. If a waveform's high time equals its low time, it is called a square wave. The length of each cycle (one positive peak and...
Laboratory 2: Transistor circuit characteristics A. Objectives: 1. To study the basic characteris...
Laboratory 2: Transistor circuit characteristics A. Objectives: 1. To study the basic characteristics of a transistor circuit. 2. To study the bias circuit of a transistor circuit. B. Apparatus: 1. DC Power supply 2. Experimental boards and corresponding components 3. Electronic calculator (prepared by students) 4. Digital camera (prepared by students for photo taking of the experimental results) 5. Laptop computer with the software PicoScope 6 and Microsoft Word installed. 6. PicoScope PC Oscilloscope and its accessories. 7. Digital multi-meter....
For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolbar, select &...
For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolbar, select "Bode Plotter". Change initial (I) and final (F frequencies to 1Hz and 200 KHz, respectively. Use a Voltage AC source as the input signal. You do not need to change any parameter from voltage AC source Connect "Bode Plotter" to input and output of your circuit...
Simulation For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolba...
Simulation For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolbar, select "Bode Plotter". Change initial (I) and final (F) frequencies to 1Hz and 200 KHz, respectively. Use a Voltage AC source as the input signal. You do not need to change any parameter from voltage AC source. Connect "Bode Plotter" to input and output of your...
EE 282-Circuit I Pre-Lab 9 Maximum Power Transfer Theorem Name Concepts: In this pre-lab we will ...
EE 282-Circuit I Pre-Lab 9 Maximum Power Transfer Theorem Name Concepts: In this pre-lab we will be leaming about Maximum Power Transfer Theorem. Maximum power is transferred to the load when the load resistance equals the thexenin equivalent, and we carry out the analysis using Thevenin's equivalent circuit. In order to do this, first build the following circuit on Mutism. 1 R1 5.1k0 R3 2 V1 R2 8kQ 6.8㏀ Fig. 1 Part 1: To find the Thevenin equivalent resistance, we...
this is a practical question where you are given a black box and
you connect it on a breadboard to a power supply,oscilloscope and
signal generator. I got stuck on how to take the measurements as im
not sure what exact measurements to take to determine the bode
amplitude plot.
thanks
do
you know how to get the bode plot of a black box circuit. And what
measurements to take using an oscilloscope and signal generator to
get values for...
Part I: Black Box A Design your first black box adhering to the following specifications A. Input Signal to Black Box A 1. A 1 kHz cosine wave with amplitude of 1V. B. Output Signal from Black Box A 1. A 1 kHz sine wave with amplitude of Hint: Use an ideal op-amp C. Explain your design process. What type of circuit did you design? Discuss D. Why did vou use an op-amp? Could another component be used instead? Why...
1. As a reference, observe the full amplitude range of the AC voltage, without limiting. R1 330 0 f=1.0 kHz 3.0 k2 out Vap = 15.0 V Figure 1. AC Circuit without limiter Construct the circuit of Figure 1. Set the function generator for a sine wave with a frequency of about 1 kHz. Begin with the AC input voltage adjusted to its minimum value, approximately 0 V. Connect Channel 1 of the oscilloscope to observe the AC input voltag...
a) Calculate the theoretical Voltage Gain, Input resistance,
and Output resistance for the circuit used in this lab. Assume
Beta= 200 and that the signal generator has an output resistance of
50ohm
find Av? Rin? Rout?
vec 20.00 XSC1 (RB 470kg Tektronix C2 HE 100F 1 2N4124 CA M - 100F RE 32.2ko RL 1ko w
C- Amplifier: Consider figure 3. This circuit uses the JFET to amplify the input signal voltage First the dc operation must be set. Use equation 1 and your previous data to calculate the value of Vas required to give I-0.5 mA. Determine the source resistance Rs needed to set this bias. Set up the circuit of figure 3 with your calculated value of Rs. Measure Vo and Vs to determine if your operating conditions are correct. Apply an input voltage...
Objectives: To learn transient behavior of series RC circuits To observe of time constant and its effect on charging process of capacitor using pulse waveforms Equipment: Oscilloscope Function generator Resistors (1 k) Capacitors (1 uF) Breadboard Pre-Lab Questions A pulse is a voltage or current that changes from one level to the other and back again. If a waveform's high time equals its low time, it is called a square wave. The length of each cycle (one positive peak and...
Laboratory 2: Transistor circuit characteristics A. Objectives: 1. To study the basic characteristics of a transistor circuit. 2. To study the bias circuit of a transistor circuit. B. Apparatus: 1. DC Power supply 2. Experimental boards and corresponding components 3. Electronic calculator (prepared by students) 4. Digital camera (prepared by students for photo taking of the experimental results) 5. Laptop computer with the software PicoScope 6 and Microsoft Word installed. 6. PicoScope PC Oscilloscope and its accessories. 7. Digital multi-meter....
For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolbar, select "Bode Plotter". Change initial (I) and final (F frequencies to 1Hz and 200 KHz, respectively. Use a Voltage AC source as the input signal. You do not need to change any parameter from voltage AC source Connect "Bode Plotter" to input and output of your circuit...
Simulation For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolbar, select "Bode Plotter". Change initial (I) and final (F) frequencies to 1Hz and 200 KHz, respectively. Use a Voltage AC source as the input signal. You do not need to change any parameter from voltage AC source. Connect "Bode Plotter" to input and output of your...
EE 282-Circuit I Pre-Lab 9 Maximum Power Transfer Theorem Name Concepts: In this pre-lab we will be leaming about Maximum Power Transfer Theorem. Maximum power is transferred to the load when the load resistance equals the thexenin equivalent, and we carry out the analysis using Thevenin's equivalent circuit. In order to do this, first build the following circuit on Mutism. 1 R1 5.1k0 R3 2 V1 R2 8kQ 6.8㏀ Fig. 1 Part 1: To find the Thevenin equivalent resistance, we...
Most questions answered within 3 hours.
-
Question 29 Which of the following is not needed in order to
prepare a statement of...
asked 9 minutes ago -
The Bureau of Labor Statistics divides the adult population into
four categories: employed, underemployed, unemployed, and...
asked 7 minutes ago -
iodination of vanillin
experiment
1. Briefly explain why the
iodination took place at the indicated position...
asked 24 minutes ago -
Hello, I have questions on Matlab. Let's say that I have an
equation. Signal x(t)= cos(2*pi*10*t)...
asked 20 minutes ago -
Fermentation carried out by year cells will produce
1. glucos
2. ethanol
3. phsophoglyceraldehyde
4. 36...
asked 20 minutes ago -
create a class in Java for a Plane
the class will include
String Data Fields for...
asked 22 minutes ago -
A jewellery material consists of 92.5 wt% of Au and 7.5 wt% of
Cu forming a...
asked 27 minutes ago -
A uniform magnetic field B=5.210 T is perpendicular to the plane
of the paper (into the...
asked 34 minutes ago -
A metal strip 8.80 cm long, 0.758 cm wide, and 0.594 mm thick
moves with constant...
asked 35 minutes ago -
The following 32-bit binary word written in hexadecimal format
represents a single RISC-V assembly instruction. What...
asked 38 minutes ago -
A
survey found that out of a random sample of 200 workers 168 said
that they...
asked 50 minutes ago -
Duck Dodgers hops in his spaceship and leaves the Earth at a
constant velocity of 0.6c...
asked 52 minutes ago