Question

7.8 A horizontal pipeline consists of a 38 mm diameter pipe, 6 m long in total. The pipe has 2 bends, each with a loss coeffi
0 0
Add a comment Improve this question Transcribed image text
Answer #1

ayg。|ア}@fr z 90orq.gly : 5089, 39 6.36レto 2.24

Add a comment
Know the answer?
Add Answer to:
7.8 A horizontal pipeline consists of a 38 mm diameter pipe, 6 m long in total. The pipe has 2 bends, each with a l...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • 2.2 A 250 mm diameter pipe is 1500 m long. When the discharge is 0.095 m3/s...

    2.2 A 250 mm diameter pipe is 1500 m long. When the discharge is 0.095 m3/s in this pipe, the pressure drop between the ends of the pipe is measured as 98.06 kPa. The elevation at the end of the pipe is 10 m below its beginning. What type of flow is this? What is the equivalent sand-grain roughness of the pipe wall? What is the Hazen-Williams roughness coefficient? How much energy is dissipated by fluid friction during each hour...

  • 5) A 6-km cast-iron (new) pipeline conveys 0.32 m/s of water at 30°C. If the pipe...

    5) A 6-km cast-iron (new) pipeline conveys 0.32 m/s of water at 30°C. If the pipe diameter is 30 cm, compare the head loss calculated (a) Darcy-Weibach equation (f = 0.0195), (b) the Hazen- William equation (Chw = 130), and (c) the Manning equation (n=0.011). Use Excel. (Max. 15 Points) 6) Pipes AB and CF in figure below have a diameter of 48 in possess a Hazen-Williams coefficient factor of 100 and carry a discharge of 120 ft/s. The length...

  • Total pipe length (including the vertical and horizontal sections) is L = 16 m. Pipe diameter...

    Total pipe length (including the vertical and horizontal sections) is L = 16 m. Pipe diameter D = 8 cm, pipe cross‐sectional area Apipe = 2 x 10‐4 m2, pipe roughness e = 0.08 mm. There is a streamline from location (1) to location (2) with an elevation change of H = 12 m. Reservoir surface area Asurf = 12 m2. Calculate the flowrate Q in the system using the recursive method (guess f and check). 1) Water flows steadily...

  • Question in the picture smooth pipe: Total length, L Diameter, d -25 mm 4 m tank...

    Question in the picture smooth pipe: Total length, L Diameter, d -25 mm 4 m tank water (pa 1,000 kg/m3, μ 0.001 kg/ms) flows from a very large tank (that is open to atmosphere) through an L 4 m total length of smooth pipe of d = 25 mm diameter at a bulk velocity of 6 m/s. The water then exits the pipe at 3 m above ground as a free jet. The pipe network contains a gate valve (V),...

  • A system using 10-inch (10") internal diameter pipe requires a selection of flanged valves. Consider 10"...

    A system using 10-inch (10") internal diameter pipe requires a selection of flanged valves. Consider 10" ball valves, gate valves, globe valves, and check valves in the fully-open position; and butterfly valves in a variety of open positions. FNW has been chosen as the equipment supplier; the relevant data sheets can be found on Desire2Learn (see below for information on valve part numbers and cor- responding files). The data sheets give valve coefficients (C,): flow rates in GPM corresponding to...

  • Water at 15°C (ρ  = 999.1 kg/m3 and μ = 1.138 × 10−3 kg/m·s) is flowing steadily in a 34-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine the pressure d...

    Water at 15°C (ρ  = 999.1 kg/m3and μ = 1.138 × 10−3 kg/m·s) is flowing steadily in a 34-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine the pressure drop, the head loss, and the pumping power requirement to overcome this pressure drop. The roughness of stainless steel is 0.002 mm.Determine the following:A)The pressure drop in _______  kPa.B)The head loss in _______  m.C)The pumping power requirement in _______  kW.

  • A 38-in pump is installed for the system below. The pipe (100-cm diameter) has a friction...

    A 38-in pump is installed for the system below. The pipe (100-cm diameter) has a friction factor of 0.012 and a total length of 20 km. Given that Ke-0.5 (pipe entrance) and K = 1.0 (pipe exit). For water at 80 degrees Fahrenheit, estimate the flow rate (in gpm), the power required (in horsepower, HP), and the net positive suction head required (in ft) to avoid cavitation for the system when the pump running. 180 m Elevation V Elevation =...

  • (100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1....

    (100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1. discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of Sin diameter cast iron. From the pump to the discharge the pipe...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT