Problem 6-80 Statics The toggle clamp is subjected to a force F at the handle. Determine the vertical clamping force ac...

Question

Question

The toggle clamp is subjected to a force F at the Problem 6-80 Statics

Answer 1

✔ Recommended Answer

Answer #1

Show the free body diagram as in Figure (1.a) ah 5a B< Take moment about point B Fen cos 30° F sin 30° F(2a)-(0 0.433Fco(a)-0

Answer 2

Similar Homework Help Questions

Problem 4 (25%) is applied to the handle of the toggle clamp, determine the resulting clamping...

Problem 4 (25%) is applied to the handle of the toggle clamp, determine the resulting clamping raw the Free Body Diagram of each member analyzed. Hint: FBD of handle and pins force at A? D at C& B and member A, C, D 70 mm 235 mm 30 mm 309 275 mm 30 mm 30
Chapter 4, Problem 4/099 Determine the magnitude of the vertical clamping force at E in terms...

Chapter 4, Problem 4/099 Determine the magnitude of the vertical clamping force at E in terms of the force P applied to the handle of the toggle clamp 70 mm 125 mmP 10 mm 13 mm 6 mm \10 mm BI Answer: E
2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is...

2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is applied at the end of the 0.375 in diameter handle. The screw is a 0.75 in-6 Acme thread (from Figure 8-3), and is 10.4 in long overall, with a maximum of 8 in possible in the clamping region. The handle and screw are both made from cold-drawn AISI 1006 steel. The coefficients of friction for the screw and the collar are 0.15. The collar,...

For the screw clamp shown, a force is applied at the end of the handle 3...

For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw centerline. The 큼 in diameter handle is made of cold-drawn AISI 1006 steel. The screw is in-10 UNC and is 8 in long, overall. The maximum possible length of screw in the clamping region is 6 in. (a) What screw torque will cause the handle to bend permanently? (b) What clamping force will the answer to part (a) cause if...
For the screw clamp shown, a force is applied at the end of the handle 3...

For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw centerline. The 큼 in diameter handle is made of cold-drawn AISI 1006 steel. The screw is in-10 in (a) What screw torque will cause the handle to bend permanently? er to part (a) cause if the thread friction is 0.15? (c) What clamping force will cause the screw to buckle? (d) Are there any other stresses or possible failures to...
80 N 6. A force of 80 N is applied to the handle of the pliers...

80 N 6. A force of 80 N is applied to the handle of the pliers as shown. Determine the clamping force exerted on the smooth pipe B and the magnitude of the force at pin A. Answers must be supported with relevant free-body diagrams and equilibrium equations AO 50 mm 45 250 mm SON

A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown ...

A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown in Figure 13. The threaded screw has a mean diameter of 12 mm and advances 2.8 mm per turn. The coefficient of static friction is 0.20. Neglecting any friction at point A Determine the force F which must be applied to the handle at C in order to i. Tighten the clamp to provide the clamping force. ii....
as shown in F (6 pts) Calculate F, needed for the clamping force For the screw...

as shown in F (6 pts) Calculate F, needed for the clamping force For the screw clamp shown below,a fore F,is applied at in-10 UNC. The collar friction is negete the end of the handle 3% in from the lang, bloka, a" shown in fipre (b). The screw is % gure (a), to as shown in Figure (c3, to be 30 ThE. clamping force (8-1) Fd π.fa_-1 т, = (8-2) o 0730 0.0860 0 003 70 0003 0.004 87 004...
Problem 21. Rod CE slips through a frictionless hole in the toggle clamp assembly shown in...

Problem 21. Rod CE slips through a frictionless hole in the toggle clamp assembly shown in the following figure. Determine Q to hold the toggle in equilibrium. Determine the force in BD. P 110 N 100 mm 10 mm 25 mm 45 m /C P. 21

ENGR 420 Statics Problem 3. (10 points) Determine the magnitude of the moment of the force...

ENGR 420 Statics Problem 3. (10 points) Determine the magnitude of the moment of the force about z axis. F-1304-20+5ORN Problem 4. (10 points) The ends of the triangular plate are subjected to three couples. Determine the magnitude of the force F so that the resultant couple moment is 500 N.m clockwise