correct answer please
correct answer please Il dimensions in millimeters 500N 500 N 22.00 10.00 15.00 10.00 R11.00 30.00 12.00 30.00 1000 N 00...
Problem 2) Combined Loading (30 points) The structure shown has a diameter of 40 mm. The length dimensions are a 500 mm and d -100 mm. Using load magnitudes of P.-3000 N, 1000 N, and B-1500 N, determine the normal and shear-stresses in the structure at point H. (Point H is co-planar with the x-y plane.) The cross-sectional properties are A 1257 mm2 J = 251,327 mm" 1,-1,-125,664 mm4 emax -5333 mm3 Present your answers in the following stress tensor...
what is the correct answer Task 10 36 Calculate the torsional section modulus W, of the profile Dimensions are in millimeters. 38 d. 885 mm? f. 262 mm 159 mm, 3 e. 111 mms a. 1110 mm 4 b. 278 mm, з с. Answer Task 10 36 Calculate the torsional section modulus W, of the profile Dimensions are in millimeters. 38 d. 885 mm? f. 262 mm 159 mm, 3 e. 111 mms a. 1110 mm 4 b. 278 mm,...
Part 1 Correct Three loads are applied to the cantilever beam shown. The cross-sectional dimensions of the beam are shown in second figure. Assume a = 10 in, h = 2 in., k =3 in, e = 4 in., P = 26 kips, Q = 21 kips, R = 10 kips, b = 9 in., and d - 13 in (a) Determine the normal and shear stresses at point K. (b) Determine the principal stresses and maximum in-plane shear stress...
(3pts): The truss is constructed of A36 steel (E -2 a cross-sectional area of 250 mm2. Answer the following s 300 Clbe wna -250 MES, AI 00 G Pa and O, 250 MPa). All truss members have (a) Determine the normal stress and strain in member CD. (b) The support at joint D uses a pin placed in double shear. The pin diameter is 20 mm Determine the average shear stress acting in the pin. 50 kN 50 kN 25...
Only point A please HOMEWORK 1: At the Cullowhee Zoo one of the most popular attractions is watching the hippos dive off of a specially constructed diving board into the Tuckaseegee River. They are magnificent, you should really go some time. The diving board consists of a very strong wall with a support pipe embedded into it with very strong concrete. The pipe is welded together with a diving board that has a hollow, rectangular cross section. BOTH THE PIPE...
A pressure vessel with dimensions do 5 in and t 3/32 in is put under the following combined loading: internal pressure P380 psi, axial load F7 kips and torque T 900 ft #. a.) Check that the pressure vessel can be classified as thin walled b.) Calculate all the types of stresses c.) Draw the stress element with values d.) Combine the stresses to determine the maximum shear stress Tmax [psi] e.) Determine the safety factor N given that the...
Please show work clearly. Thanks 4. Suppose you had n matrices with dimensions: ai xbi ,a2 x b2. . . . ,a,, X bn. Your goal is to determine, given two integers s and t, whether it is possible to multiply a sequence from the list of given matrices together, in any order and possibly not using all of the matrices, to end up with a matrix with dimensions s × t. For example, if the list of matrix dimensions...
Please provide a correct answer to these questions. The material is structural steel with of = 220 MPa, E = 200 GPa, v = 0.3, and a = 12x10-6 / 0 C The steel rod (Figure 1) is constrained between two rigid surfaces. It has a diameter D = 20 mm and is subjected to load P = 20 kN. Consider the following value below The reaction at 'A' = 13.13 KN(t) The reaction at 'B' = 6.67 KN(t) The...
Please Answer the remainer of the questions parts. thank you! Part 1 Your Answer Correct Answer Correct Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of S - 55ksi, 5-15 ks, and S. - 14 ksi. m. Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the...
Will rate for Correct answer, please show full work The rectangular plate is deformed into the shape shown by the dashed lines. The plate is made of a material whose stress-strain diagram is given below. a) Calculate the normal strain of diagonal AC. b) Calculate the shear strain at corner A. c) What stress is needed to cause the strain calculated at A? d) After all stress is removed from the plate, what is the permanent strain at corner A?...