Answer
For Compression member with both end hinged,
Effective Length = Total length = 26 feets.
Total Service Load = Dead Load + Live Load
= 165 + 535
= 700 kips.
A beam is a flexural member whereas column is a compression member.
How to chick if a concrete beam is over-reinforced ? A compression member is subjected to service loads of 165 kips...
A compression member is subjected to service loads of 165 kips dead load and 535 kips live load. The member is 26 feet long and pinned in each end. Use (A572 - Gr 50) steel and select a W14 shape 1) Use the equations; 2) Use the tables; 3) Use STAAD.Pro or any other commercial software to verify your design 4) Compare and comment on your results.
2. Design Wide flange column section only of A992 steel to serve as a pinned- end main member column 30 ft long to carry an axial compression loads in a braced structure, based on AISC LRFD method. The dead load is 50 kips A992 13-0" and live load is 70 kips. The member has strong axis direction supported at 17ft height from the bottom of the column. Dead load is 20 kips and live load is 40 kips. Assume the...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD=500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fe 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two layers), 26...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
Problem 5: Design of Idealized Compression Member A 20-ft long column is pinned at the bottom and fixed against rotation, but free to translate, at the top. It must support a service dead load of 110 kips and a service live load of 110 kips. a) Select the lightest W12 of A992 steel. Use the column load tables b) Select the lightest W18 of A992 steel. Use the trial-and-error process.
Name: Date: Part II: Numerical responses 1. (+35) Design a rectangular reinforced concrete beam (tension steel only) for a simply span of 30 ft. Uniform service loads are 2 kips/ft dead load (included the beam weight) and 3.0 kips/ft live load. The beam is to be not exceed 16 inch wide due to column size. Use fe'=4000psi and fy 60000psi. Sketch your design and calculate Mn for the beam you design. Note: this is an open-end design for you to...
Q3) A simply supported beam is subjected to a uniform service dead load of 2.3 kips/ft (excluding the weight of the beam), a uniform service live load of 3.0 kips/ft. The beam is 30 feet long, and deflection not to exceed L/360. The beam has continuous lateral support, and A992 steel is used. Is a W27 x 84 adequate?
Consider the beam subjected to a concentrated load consisting of 2.25 kips of dead load and 5.55 kips of live load at point B. Find maximum factored beam shear, moment, and deflection. Consider the beam and loading given below. The beam is subjected to a concentrated load consisting of 2.25 kips of dead load and 5.55 kips of live load at point B. Neglect beam weight. You may use any information from the AISC Manual, a) Draw the general shape...
A reinforced concrete cantilevered beam with a span of 5 m extends from the wall, as shown in the figure below. The beam has a rectangular cross-section and supports a uniform dead load (DL) of 15 kN/m (excluding the self-weight) and a uniform live load (LL) of 25 kN/m. The beam width is restricted to 400 mm. Use 10M stirrups and 25M bars for tension steel. The maximum aggregate size is 20 mm. 1ie 5.5. beam is located in the...
Problem 22. Two-story, one-bay unbraced frame shown below is subjected to gravitational dead and live loads and wind lateral load. The columns are made of W18x65 (I,-1070 in , Ag- 19.1 in2, r-7.49 in, ry-1.69 in) and beams are made of W18x71 (1, 1170 in). The table below shows the moments at the ends of column 4-5 due to three load cases. The frame is fully braced in lateral direction. Use Grade50 steel Bending is about strong axis. All gravity...