Vpp R R Va -Vut R Assune both transisters insat hinIK(Vs - Va) a) Find Vaa...
can
anyone please write an explanation as well when answering? thank
you for your assistance
R Vin nwww Vot) Take a square wave signal from Function Generator for Vin through AO 0 port. Then set Vn and Vas to Al 0 and Al 1 respectively in order to observe the input and output waveform using oscilloscope. Vary the frequency of the square wave input according to the values shown in the table below. Then, observe the amplitude of the output...
F1 শ। Problem 3: For the circuit in Fig. 3, find Vo/Vs in terms of a, Ri, R2, Rs and Ra. If R-R2-R)-Ra, what value of a will produce Vo/Vs |-10? RI + Va RA R3 alo R2 V's Fig. 3
please solve the following (simple steps):
Q1)
i
ii
iii
and
Q2)
i
ii
For the circuit shown: XSC1 XFG1 P 1 2 3 4 2 100mH 20% 10k Key A 100nF 0 1) Find equations (step response) for both vc and i for the following cases: i. ii, iii. R= 12%, R 20%, and R:-29%. 2) Using a square wave with a frequency of 200 Hz and 2-Vpp, simulate the relationship betwee the input, vi, and the output, v3,...
can
you help with both problems
4. Find I and Va in the circuit below 8 k 2 k0 36 kn $4 k V 12 V 5. Determine in the circuit below 6 k0 4 k 12 kn 2 k 4 k 16 k )12 V
Hi everyone, I have a question about active filter, including a
simulation,
Please provide the screen capture.
Thanks.
5. Active Filter - III Consider the RC op-amp circuit shown in Fig. 5.4. Vin(t) is a sinusoidal signal with Vpp = 1 V, Rı = 10 ㏀ , R, = 20 ㏀ , and C,-C,-0.01 μF. Use Vcc-15V, The capacitors have zero initial energy stored. Ri 741 C1 C2 Volt) Fig. 5.5: Active filter - III (a) Find the transfer function...
pls answer 4,5,6 and 7
An) a) Find the magnitude of both vectors. b) Find dot product and cross product of both vectors c) Find the projection of w onto v 2) Let а:31 + 5, + 7k and b--6r +-10, + mk where m e R. a) Find the value for m such that vectors are orthogonal b) Find the value of m such that the cross product of the vectors is zero 3) a) Find the distance from...
i
need some help
See the table for the values of R (in kiloohms), C, and C2 (both in millifarads) for the circuit diagram on this page. v(t) as shown in the graph. VA 2. (3 points each) For the circuit shown here, find vo at 3s, 5s, and 9s. : 34m avt) 20V Page 4 of 7
See the table for the values of R (in kiloohms), C, and C2 (both in millifarads) for the circuit diagram on this...
Q.2 Given Vsi V's2-Vs SV, and Ri-R-Rs 1002. a) Simplify the circuit into one with a single voltage source Vr and a single resistor Rr b) Find the value of Vr and RT. c) Find the value of I d) Find the voltage values with reference to ground VA, VB, Vc, Vo. e) Using Kirchhoff's Voltage Law, show that the value of is one that you obtained in c) -IR R 4) во RT R2 61 レD-iA: 5V DI I...
Block A of mass mA is moving horizontally with speed Va along a frictionless surface. It collides elastically with block B of mass mB that is initially at rest. After the collision block B enters a rough surface at x =0 with a coefficient of kinetic friction that increases linearly with distance μ(x) = bx for 0 ≤ x ≤ d, where b is a positive constant. At x=d block B collides with an unstretched spring with spring constant k...
[20] 1. For the circuit below. (a) Find It for an arbitrary Vs, R, and Ru. (b) What component would you normally expect would have a strong effect on 1,, but does not? What does this component “think” it is connect to? Explain.