a. Largest - South Louisiana
Smallest - Port Arthur
b.
c. Historgram 1, represents the accurately the data
Most of the top 25 ports handle less than 75 million tons. Only 5 of the ports handle above 75 million tons
Based on the tons handled in a year, the ports listed below are the 25 busiest...
Develop a piecewise linear transfer function for the calibration data shown below (and on your handout) Use a (s,T) coordinate of (5.5,0) as your transition point. Report your answer as an equation using the equation editor function. 225 200 175 150 U 125 2 100 O 75 50 - 25 ト + ト + 25 75 89 10 Stimulus (mV) Develop a piecewise linear transfer function for the calibration data shown below (and on your handout) Use a (s,T) coordinate...
Based on historical data, daily demand of a product is normally distributed with a mean of 200 and standard deviation of 50. Develop a spreadsheet simulation model by simulating 300 observations of demand. After simulation freeze the simulated demand values. Use Analysis ToolPak ? Histogram create a histogram visualizing the demand distribution using bins: 100, 125, 150, 175,...,300. Use Analysis ToolPak ? Descriptive Statistics to compute the descriptive statistics metrics of the simulated values. Interpret skewness of the simulated demand....
Question 6 Select one answer. Based on the results of a nation-wide study, the number of contacts programmed into cell phones are summarized on the following boxplot: 10 points 1 25 50 75 100 125 150 175 200 225 Which of the following is true about this data? A. ︵ The lowest observation is an outlier. B. O The highest observation is an outlier. C. The data is skewed left. D. O The data is skewed right. E. O There...
Question 1 of 11 (1 point) View problem in a pop-up 22 Section Exercise 2a The number of bears killed in 2010 for 52 counties in Pennsylvania is shown in the frequency distribution. Class limits Frequency 18 12 7 1-25 26-50 51-75 76-100 101-125 126-150 151-175 176-200 201-225 226-250 6 2 3 0 2 0 2 Total 52 Source: Pennsylvania State Game Commission Download Data Part 1 out of 3 Which of the following visual displays below is a histogram?...
12. Consider the data taken in lab for the following reaction. Given the slopes of tangent lines for two data points, solve for the reaction rate constant for the following reaction. AB → AB 046 Rate of Change of (AB) 062 036 014 [AB] When (AB) = 0.302. AAB)-267 x 10 st 02 024 022 016 0.14 012 When (AB) = 0.149, [AB]= 6.51 x 10 00 000 004 > so 75 100 125 150 175 200 225 230 275...
Q FC VC TC AFC AVC ATC MC 0 15 000 0 15 000 - - - - 100 15 000 15 000 30 000 150 150 300 15 000 200 15 000 25 000 40 000 75 125 200 10 000 300 15 000 37 500 52 500 50 125 175 12 500 400 15 000 75 000 90 000 375 187.5 225 37 500 500 15 000 147 500 162 500 30 295 325 72500 600 15 000...
In regards to question 3, will cavitation occur based on the NPSH available vs NPSH required? Water is pumped from a reservoir to a large receiver vessel which is maintained at p3 = 6 bar through the operation of the pump and a high pressure nitrogen supply that bleeds into the tank through a regulator. The water enters through an opening at the top of the vessel. A drain is provided at the low point in the system. Elevations are...
Answer in order please thank you. Question1 A survey was conducted from a random sample of 8225 Americans, and one Selecd variable that was recorded for each participant was their answer to the question, "How old are you?" 1o points The mean of this data was found to be 42, while the median was 37. What does this tell you about the shape of this distribution? A. O It is symmetric. B. O It is skewed left. C. There is...
I just want to know if I have balanced this correctly and not made any mistakes while inputting it. Thanks ANTONELLI'S ACCOUNTING SERVICES Beginning Transaction 1 Transaction 2 Total Equity 1850 Zero Proof ASSETS LIABILITIES OWNER'S EQUITY AIR AR Total AVP Total Antonelli Cash Jones Trave F. Leonel Supplies Equipment Assets Best Office astside Ney Bank Loan Liabilities Capital 275 300 350 700 900 2525 175 500 675 1850 2000 4525 2 000 2675 -1300 1 300 4525 2675 200...
Can somone show me how to do the 1st problem? Need to find the LS and SS for the fit and the LH and SH for the hole. Fits are all SHAFT BASIS METRIC but the shaft and hole diameters can not be used right out of the table. This is because the 3mm shaft tolerance does not match. You will need to lookup the "Fit" from the table, and then use the LS (Largest Shaft) and SS (Smallest Shaft)...