3. Determine the loadings at the internal cut when the solid rod is subjected to the...

Question

Question

3. Determine the loadings at the internal cut when the solid rod is subjected to the loading shown. 100 mm 200 mm cut 1,270 N

Answer 1

Answer #1

Please rate
if any mistake in this answer please comment i will clarify your doubt . thank you

Answer 2

Similar Homework Help Questions

The solid rod is subjected to the loading shown

*8-48. The solid rod is subjected to the loading shown. Determine the state of stress at point B, and show the results on a differential volume element at this point. 8-49. The solid rod is subjected to the loading shown. Determine the state of stress at point C, and show the results on a differential volume element at this point.
X The bar has a diameter of 47.8 mm. If it is subjected to the loadings...

X The bar has a diameter of 47.8 mm. If it is subjected to the loadings shown (P = 755 N, T = 56.5 Nm, L1 = 200 mm, and L2 = 100 mm, determine the shear stress in MPa) at point A. Note: Your answer should include requested units and be to 3 decimal places. L2 11 A B X 30° Selected Answer: [None Given] Correct Answer: 3.121 + 2% (MPa)
Learning Goal: To determine the state of stress in a solid rod using the principle of...

Learning Goal: To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 55 mm and is subjected to the loading shown. Let a = 190 mm, b = 220 mm , c = 350 mm, d = 240 mm , and P = 4.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 b В...

The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the...

The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the absolute maximum and minimum shear stresses in the shaft's surface and specify their locations, measured from the free end. 10-25. The solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the required diameter d of the shaft if the allowable shear stress for the material is Tallow = 60 MPa. 400 N·m 4 kN.m/m А. < 0.2 m 0.2 m...
Problem 1 A beam with an I-cross section, is subjected to the internal loadings shown. Determine...

Problem 1 A beam with an I-cross section, is subjected to the internal loadings shown. Determine the stresses acting on particles H and K and sketch them on a properly oriented element. 35 mm 6 mm H13.2 kN 15 mm 8.5 kN 6 mm 65 mm 2.1 kN-m 15 mm 50 mm 6 mm
A composite bar BCDE consists of three parts: solid cylindrical rod BC, solid cylindrical rod CD,...

A composite bar BCDE consists of three parts: solid cylindrical rod BC, solid cylindrical rod CD, and pipe DE. Rod BC is welded to rod CD at C, and rod CD is welded to pipe DE at D. The composite bar is fixed at E. The bar is subjected at B to an axial force of 20 kN, and is also subjected to four other forces: two forces of magnitude 2P at section C and two forces of magnitude P...

3. A square rod of 500 mm long with a width of 10 mm is subjected...

3. A square rod of 500 mm long with a width of 10 mm is subjected to a load of 40000 N., The stress-strain behavior is shown in the Figure below. Based on the information, please answer the following questions: (Note: Pa = N/㎡, J = Nm) (a) Compute the applied stress (5 points). 70 Tensile strength 450 MPa (65.000 ps) -60 400 103 ps MPa 40厂 50 300 40 Yield strength30 250 MPa (36.000 ps) 200 100 20 10...
The 30-mm-diameter A992 steel rod is subjected to loading shown. Determine the displacement of end C...

The 30-mm-diameter A992 steel rod is subjected to loading shown. Determine the displacement of end C E = 200 *109 3 30 LN 90 KN 30 EN -600 mm 300 mm -
Problem 4 (20 pts) oss section through point D of Determine the resultant internal loadings acting...

Problem 4 (20 pts) oss section through point D of Determine the resultant internal loadings acting on the cr member AB. 50 mm 50mm 300 mm 150 nm A D 70 N m 200 mm FBD

Combined loading A rod with the diameter of 20 mm is subjected to a force P...

Combined loading A rod with the diameter of 20 mm is subjected to a force P - 1800 N, as shown in the figure. The rod is fixed to the wall at Point C.L.- 50 mm and L-200 mm. Determine the magnitude of the shear stress MPa at Point Blocated on the surface of the rod on the designated positive z axis (rounding to two decimal places).