Homework Answers
Add Answer to:
Figure 5.2 shown a hollow brass pipe with 125 mm diameter and 6 mm thickness (c)...
1.5-7 A hollow, brass circular pipe ABC (oce figure supports a load P, 118 kN acting at the top A...
please help ASAP
1.5-7 A hollow, brass circular pipe ABC (oce figure supports a load P, 118 kN acting at the top A second load P -98 kN is uaiformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are 31 mm ,,-12 mm, dae" 57 mm, and tac· 9 mm, respectively. The modulus of clasticity is 96 GPa. When both loads are fully applied, the wall thickness of...
4.A thin-walled cylindrical column carries a weightless arch and is loaded as shown in Figure 4. The column has an internal diameter of 250 mm with a thickness of 2 mm Given: E-200 GPa and 0.3 The an...
4.A thin-walled cylindrical column carries a weightless arch and is loaded as shown in Figure 4. The column has an internal diameter of 250 mm with a thickness of 2 mm Given: E-200 GPa and 0.3 The answer to each part of the question is to be used for subsequent parts (a)Determine the stresses on the outer surface of the cylinder at points A and B due to (8 marks) (b) Determine the minimum internal pressure p required if the...
Q-1 A solid circular rod with a diameter d = 18 mm is shown in Figure...
Q-1 A solid circular rod with a diameter d = 18 mm is shown in Figure Q-3. The rod is made of an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v=0.32. When subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety of 1.75, a) Determine the magnitude of the safe allowable load P. pts.] b) If we have a 12 mm...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm and thickness of t = 8 mm. The steel has a shear modulus of elasticity E = 200 GPa and v = 0.3. For an applied torque of 35 kN m, determine the following quantities: a) Shear stress at the mid-center of the thickness t of the shaft. [2] b) Shear stress on the outer surface. [1] c) Shear stress in the inner surface,...
Find the minimum required thickness tmin for a steel pipe column of length L-3.6 m and [25 pts.] Q-3 outer diameter d=1...
Find the minimum required thickness tmin for a steel pipe column of length L-3.6 m and [25 pts.] Q-3 outer diameter d=160 mm supporting an axial load P-240 kN (See Fig. below). The column is fixed at the base and free at the top. (Use E 200 GPa and Sy-250 MPa.) -The critical 1loading is calculated from Euler's formula, L 2EI Per er (Le/r Le equivalent length ka/
Find the minimum required thickness tmin for a steel pipe column of...
According to machine elements 1 Q-1 A solid circular rod with a diameter d= 18 mm...
According to machine elements 1
Q-1 A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v = 0.32. When subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety of 1.75, a) Determine the magnitude of the safe allowable load P. [18 pts.]...
A pipe with an outside diameter of 175 mm and a wall thickness of 6 mm...
A pipe with an outside diameter of 175 mm and a wall thickness of 6 mm is subjected to the loadings shown in the figure below. Р. H For this analysis, use the following values: Distances, Loads, and Moments. a = 400 mm Px = 40.5 kN Py = 68.5 kN T = 35 kN-m (a) Calculate the maximum in-plane shear stress Tmax at point Hon the outer surface of the pipe if there is no internal pressure (i.e.,p-OkPa). (Note:...
Review The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD,...
Review The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF, and a rig d bar G. The modulus of elasticity for red brass C83400 is 101 GPa, for 304 stainless steel 193 GPa. (Figure 1) Part A If the horizontal displacement of end F of rod EF is 0.46 mm, determine the magnitude of P. Express your answer to three significant figures and include the appropriate...
A pipe with an outside diameter of 150 mm and a wall thickness of 5 mm...
A pipe with an outside diameter of 150 mm and a wall thickness of 5 mm is subjected to the loadings shown in the figure below. P PO a For this analysis, use the following values: Distances, Loads, and Moments. a = 450 mm Px = 11.5 kN Py = 25.5 kN T = 15 kN-m (a) Calculate the maximum in-plane shear stress Tmax at point Hon the outer surface of the pipe if there is no internal pressure (i.e.,...
The concrete [E = 29 GPa] pier shown in the figure is reinforced by four steel...
The concrete [E = 29 GPa] pier shown in the figure is
reinforced by four steel [E = 200 GPa] reinforcing rods,
each having a diameter of 19 mm. Assume P = 680 kN,
L = 2.10 m, and a = 275 mm. If the pier is
subjected to an axial load of 680 kN, determine
(a) the normal stress (positive if tensile and negative if
compressive) in the concrete and in the steel reinforcing
rods.
(b) the deflection of...
please help ASAP
1.5-7 A hollow, brass circular pipe ABC (oce figure supports a load P, 118 kN acting at the top A second load P -98 kN is uaiformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are 31 mm ,,-12 mm, dae" 57 mm, and tac· 9 mm, respectively. The modulus of clasticity is 96 GPa. When both loads are fully applied, the wall thickness of...
4.A thin-walled cylindrical column carries a weightless arch and is loaded as shown in Figure 4. The column has an internal diameter of 250 mm with a thickness of 2 mm Given: E-200 GPa and 0.3 The answer to each part of the question is to be used for subsequent parts (a)Determine the stresses on the outer surface of the cylinder at points A and B due to (8 marks) (b) Determine the minimum internal pressure p required if the...
Q-1 A solid circular rod with a diameter d = 18 mm is shown in Figure Q-3. The rod is made of an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v=0.32. When subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety of 1.75, a) Determine the magnitude of the safe allowable load P. pts.] b) If we have a 12 mm...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm and thickness of t = 8 mm. The steel has a shear modulus of elasticity E = 200 GPa and v = 0.3. For an applied torque of 35 kN m, determine the following quantities: a) Shear stress at the mid-center of the thickness t of the shaft. [2] b) Shear stress on the outer surface. [1] c) Shear stress in the inner surface,...
Find the minimum required thickness tmin for a steel pipe column of length L-3.6 m and [25 pts.] Q-3 outer diameter d=160 mm supporting an axial load P-240 kN (See Fig. below). The column is fixed at the base and free at the top. (Use E 200 GPa and Sy-250 MPa.) -The critical 1loading is calculated from Euler's formula, L 2EI Per er (Le/r Le equivalent length ka/
Find the minimum required thickness tmin for a steel pipe column of...
According to machine elements 1
Q-1 A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v = 0.32. When subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety of 1.75, a) Determine the magnitude of the safe allowable load P. [18 pts.]...
A pipe with an outside diameter of 175 mm and a wall thickness of 6 mm is subjected to the loadings shown in the figure below. Р. H For this analysis, use the following values: Distances, Loads, and Moments. a = 400 mm Px = 40.5 kN Py = 68.5 kN T = 35 kN-m (a) Calculate the maximum in-plane shear stress Tmax at point Hon the outer surface of the pipe if there is no internal pressure (i.e.,p-OkPa). (Note:...
Review The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF, and a rig d bar G. The modulus of elasticity for red brass C83400 is 101 GPa, for 304 stainless steel 193 GPa. (Figure 1) Part A If the horizontal displacement of end F of rod EF is 0.46 mm, determine the magnitude of P. Express your answer to three significant figures and include the appropriate...
A pipe with an outside diameter of 150 mm and a wall thickness of 5 mm is subjected to the loadings shown in the figure below. P PO a For this analysis, use the following values: Distances, Loads, and Moments. a = 450 mm Px = 11.5 kN Py = 25.5 kN T = 15 kN-m (a) Calculate the maximum in-plane shear stress Tmax at point Hon the outer surface of the pipe if there is no internal pressure (i.e.,...
The concrete [E = 29 GPa] pier shown in the figure is
reinforced by four steel [E = 200 GPa] reinforcing rods,
each having a diameter of 19 mm. Assume P = 680 kN,
L = 2.10 m, and a = 275 mm. If the pier is
subjected to an axial load of 680 kN, determine
(a) the normal stress (positive if tensile and negative if
compressive) in the concrete and in the steel reinforcing
rods.
(b) the deflection of...
Most questions answered within 3 hours.
-
While rotating the tires on your car you notice a rock [mass =
0.1 Kg] stuck...
asked 16 minutes ago -
Using MARS simulator, write MIPS programs according to
the following scenarios: Receive a positive integer number...
asked 2 hours ago -
An object in front of a concave mirror has a real image that is
11.5 cm...
asked 2 hours ago -
Consider the reaction, C3 H8 + O2 --> CO2 + H2O. How many
moles of O2...
asked 4 hours ago -
You and your opponent both roll a fair die. If you both roll the
same number,...
asked 4 hours ago -
In a study of the accuracy of fast food drive-through orders,
Restaurant A had 257 accurate...
asked 4 hours ago -
Identify and describe in detail the four categories of
institutions that could be included in a...
asked 4 hours ago -
In python
class Customer:
def __init__(self, customer_id, last_name, first_name, phone_number, address):
self._customer_id = int(customer_id)
self._last_name =...
asked 4 hours ago -
What is an example of a limitation in implementing a new
ERP system and how it...
asked 4 hours ago -
In a section of 9.7cm of an artery with a radius of 2.6mm there
is a...
asked 4 hours ago -
the two carboxylic acid groups of aspartic acid have different
acidities with pKa values of 2.1...
asked 4 hours ago -
Would CuCO3 aqueous salt combined with calcium chloride
form a solid precipitate? If so, what would...
asked 4 hours ago