A solid square rod is cantilevered at one end, as shown below. The rod is 0.6...
A solid square rod is cantilevered at one end, as shown below.
The rod is 0.6 m long and supports a completely reversing
transverse load at the other end of 2 kN. The material
is AISI 1080 hot-rolled steel with Sut = 770 Mpa and
Sy = 420 MPa. If the rod must support this load for
104 cycles with a design factor of 1.5, what dimension
should the square cross section have? Neglect any stress
concentration at the support end. Use surface factor ka
= 0.488, size factor kb = 0.85, and all other factors
equal to one.
Please explain. Thank you.
Homework Answers
Add Answer to:
A solid square rod is cantilevered at one end, as shown below. The rod is 0.6...
6-13 A solid square rod is cantilevered at one end. The rod is 0.6 m long...
6-13 A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±2 kN. The material is AISI 1080 hot-rolled steel If the rod must support this load for 101 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end
A solid square rod is cantilevered at one end. The rod is 1 m long and...
A solid square rod is cantilevered at one end. The rod is 1 m long and supports a completely reversing transverse load at the other end of ±1.5 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 4 × 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. Determine the size of the cross-section.The size of the cross-section...
A beam with a square cross-section of linch X 1inch is cantilevered at one end, and...
A beam with a square cross-section of linch X 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress og...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress Og...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end,...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress Oa...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end,...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress Om and alternating stress oa...
The shaft shown in Figure is supported by bearings cach end, which have bores of 20.0...
The shaft shown in Figure is supported by bearings cach end, which have bores of 20.0 mm. Design the shaft to carry the given load if it is steady and the shaft is stationary. Make the dimension a as large as possible while keeping the stress safe. Determine the required diameter in the middle portion. The maximum fillet permissible is 2.0 mm. Use SAE 1137 cold-drawn steel. Use a design factor of 3 The material properties are as follows:- Q-1...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 1201bf (downward) to F= -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress og at...
simply supported reinforced concrete beam of rectangular section is hung on the left end by a 400mm square post working in tension, as shown in the figure below. The beam supports a uniform dead l...
simply supported reinforced concrete beam of rectangular section is hung on the left end by a 400mm square post working in tension, as shown in the figure below. The beam supports a uniform dead load (DL) gf 100 KN/m (excluding its own weight) and upiform live load LL) of 40KN/m. The beam is reinforced with 025 longitudinal rebars with 40mm cleat cover to the stirrups. Material properties: fy 420 MPa, fe 25 MPa. Beam dimension b 400mm and h 600mm....
please solve with details Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered t...
please solve with details
Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20° and a helix angle of 15o. The pitch diameter for the gear is 105.1814 mm (4.141 in). A spacer is used to position the gear relative to bearing C. The...
6-13 A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±2 kN. The material is AISI 1080 hot-rolled steel If the rod must support this load for 101 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end
A beam with a square cross-section of linch X 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress og...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress Og...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress Oa...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress Om and alternating stress oa...
The shaft shown in Figure is supported by bearings cach end, which have bores of 20.0 mm. Design the shaft to carry the given load if it is steady and the shaft is stationary. Make the dimension a as large as possible while keeping the stress safe. Determine the required diameter in the middle portion. The maximum fillet permissible is 2.0 mm. Use SAE 1137 cold-drawn steel. Use a design factor of 3 The material properties are as follows:- Q-1...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 1201bf (downward) to F= -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress og at...
simply supported reinforced concrete beam of rectangular section is hung on the left end by a 400mm square post working in tension, as shown in the figure below. The beam supports a uniform dead load (DL) gf 100 KN/m (excluding its own weight) and upiform live load LL) of 40KN/m. The beam is reinforced with 025 longitudinal rebars with 40mm cleat cover to the stirrups. Material properties: fy 420 MPa, fe 25 MPa. Beam dimension b 400mm and h 600mm....
please solve with details
Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20° and a helix angle of 15o. The pitch diameter for the gear is 105.1814 mm (4.141 in). A spacer is used to position the gear relative to bearing C. The...
Most questions answered within 3 hours.
-
A combustion reaction is describes as a carbon source reacting
with oxygen and producing carbon dioxide...
asked 6 minutes ago -
Buckminsterfullerence is a recently allotrope of carbon in which
carbon atoms form molecules of formula C_60,...
asked 8 minutes ago -
Lower Equitorial and Upper Equitorial are the same except Lower
Equitorial has a larger capital stock....
asked 13 minutes ago -
how do you think that pH of a jar where you have added a certain
amount...
asked 23 minutes ago -
If the Federal Reserve increases the reserve requirement, what
will happen to the Money Supply in...
asked 18 minutes ago -
Suppose that market demand for a good is given by Q = 9 - 0.3 P...
asked 24 minutes ago -
two thin lenses are separated by a distance x. The first lens
has a focal length...
asked 26 minutes ago -
The computer that controls a bank's automatic teller machine
crashes a mean of 0.6 times per...
asked 29 minutes ago -
`1) How is -9 (base 10) represented in 8-bit two's complement
notation?
a) 00001001
b)11110111
c)11110110...
asked 39 minutes ago -
A 10.000 g sample of water contains 11.19% H by mass. what
should be the %H...
asked 56 minutes ago -
Consider an investment game among 2 players. Each player can
either invest,
i, or not invest,-i....
asked 54 minutes ago -
The time taken to complete a particular task is normally
distributed with a standard deviation of...
asked 1 hour ago