Homework Answers
Add Answer to:
Problem 1.72 Copy The tension member is fastened together using TWO bolts, one on each side...
I can't figure this one out. The tension member is faster is fastened together using two bolts, one on each side of t...
I can't figure this one out.
The tension member is faster is fastened together using two bolts, one on each side of the member as shown. Each bolt has a diameter of 0.3 in. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is tau allow = 12 ksi and the allowable average normal stress id sigma allow = 20 ksi.
Three wooden planks are fastened together by a series of bolts to form a column. The...
Three wooden planks are fastened together by a series of bolts to form a column. The diameter of each bolt is 12-mm and the inner diameter of each washer is 16-mm, which is slightly larger than the diameter of the holes in the planks. Determine the smallest allowable outer diameter d of the washers, knowing that the average normal stress in the bolts is 32 MPa and that the bearing stress between the washers and the planks must not exceed...
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts...
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is fail = 350 MPa. Use a factor of safety for shear of F.S. = 2.5. 30 mm 80 KN 30 mm 40 KN 40 KN
4. This joint is fastened with two bolts. Determine the required diameter for the bolts if...
4. This joint is fastened with two bolts. Determine the required diameter for the bolts if the allowable average shear stress is 120 MPa. Would you expect the load-carrying capacity of the single flat bar to increase, decrease, or stay the same if you increased the diameter of the bolts? No calcs required to answer this question. 30 mm80 kN 30 mm 40 kN 40 kN
CIVL3322 Su18 Homework Set 1 Review Problem 1.3 The allowable normal stress for member BC is...
CIVL3322 Su18 Homework Set 1 Review Problem 1.3 The allowable normal stress for member BC is allow-29 ksi and the allowable shear stress for the pins is Tallow 10 ksi (Figure 1) Part A Determine the required thickness of member BC Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 t- 1 Value Units Submit Request Answer ? Part B 60 Determine the required diameter of the pin at A Express your answer...
Part A Thres identical boards are bolted together to form the built-up beam. Each bolt has...
Part A Thres identical boards are bolted together to form the built-up beam. Each bolt has a shear strength of 1.1 kip and the bults are spaced at a distance of s7 in Figure 1) If the wood has an allowable shear stress of 450 pei determine the maxinum allowabde internal shear V that can actt Express your answer to three significant figures and inclade the appropriate units. 1 of 1 2 in Submit 2 in Provide Feedback
Member CB has a square cross section of 30 mm on each side. (Figure 1) Part...
Member CB has a square cross section of 30 mm on each side. (Figure 1) Part A Determine the largest intensity w of the uniform loading that can be applied to the frame without causing either the average normal stress or the average shear stress at section b-b to exceed o= 12 MPa and t= 16 MPa, respectively. Express your answer to three significant figures and include appropriate units. ? c': Å * * o a Value Units Figure <...
Part A The cotter is used to hold the two rods together. (Figure 1) All parts...
Part A The cotter is used to hold the two rods together. (Figure 1) All parts are made of steel for which the failure normal stress is fail = 510 MPa and the failure shear stress is Trail = 365 MPa. Use a factor of safety of (F.S.)t = 2.30 in tension and (F.S.), = 1.71 in shear. Determine the smallest thickness t of the cotter. Express your answer to three significant figures and include appropriate units. de = Value...
The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling...
The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smaller pipe has an outer diameter of 18.75 mm and an inner diameter of 17 mm, whereas the larger pipe has an outer diameter of 25 mm and an inner diameter of 21.5 mm. The pipe is tightly secured to the wall at C. The couple shown is applied to the handles of the wrench. (Figure 1) Part A Determine the...
Learning Goal: To determine the maximum shear force that can be applied to two shafts of...
Learning Goal: To determine the maximum shear force that can be applied to two shafts of varying cross sections: a solid square shaft and a hollow square shaft. The two square cross sections shown below (Figure 1) are each subjected to a vertical shear force, V. The side length of each cross section is s = 6.00 in and the side length of the hollowed- out portion of the second cross section is r = 2.25 in. The maximum allowable...
I can't figure this one out.
The tension member is faster is fastened together using two bolts, one on each side of the member as shown. Each bolt has a diameter of 0.3 in. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is tau allow = 12 ksi and the allowable average normal stress id sigma allow = 20 ksi.
Three wooden planks are fastened together by a series of bolts to form a column. The diameter of each bolt is 12-mm and the inner diameter of each washer is 16-mm, which is slightly larger than the diameter of the holes in the planks. Determine the smallest allowable outer diameter d of the washers, knowing that the average normal stress in the bolts is 32 MPa and that the bearing stress between the washers and the planks must not exceed...
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is fail = 350 MPa. Use a factor of safety for shear of F.S. = 2.5. 30 mm 80 KN 30 mm 40 KN 40 KN
4. This joint is fastened with two bolts. Determine the required diameter for the bolts if the allowable average shear stress is 120 MPa. Would you expect the load-carrying capacity of the single flat bar to increase, decrease, or stay the same if you increased the diameter of the bolts? No calcs required to answer this question. 30 mm80 kN 30 mm 40 kN 40 kN
CIVL3322 Su18 Homework Set 1 Review Problem 1.3 The allowable normal stress for member BC is allow-29 ksi and the allowable shear stress for the pins is Tallow 10 ksi (Figure 1) Part A Determine the required thickness of member BC Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 t- 1 Value Units Submit Request Answer ? Part B 60 Determine the required diameter of the pin at A Express your answer...
Part A Thres identical boards are bolted together to form the built-up beam. Each bolt has a shear strength of 1.1 kip and the bults are spaced at a distance of s7 in Figure 1) If the wood has an allowable shear stress of 450 pei determine the maxinum allowabde internal shear V that can actt Express your answer to three significant figures and inclade the appropriate units. 1 of 1 2 in Submit 2 in Provide Feedback
Member CB has a square cross section of 30 mm on each side. (Figure 1) Part A Determine the largest intensity w of the uniform loading that can be applied to the frame without causing either the average normal stress or the average shear stress at section b-b to exceed o= 12 MPa and t= 16 MPa, respectively. Express your answer to three significant figures and include appropriate units. ? c': Å * * o a Value Units Figure <...
Part A The cotter is used to hold the two rods together. (Figure 1) All parts are made of steel for which the failure normal stress is fail = 510 MPa and the failure shear stress is Trail = 365 MPa. Use a factor of safety of (F.S.)t = 2.30 in tension and (F.S.), = 1.71 in shear. Determine the smallest thickness t of the cotter. Express your answer to three significant figures and include appropriate units. de = Value...
The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smaller pipe has an outer diameter of 18.75 mm and an inner diameter of 17 mm, whereas the larger pipe has an outer diameter of 25 mm and an inner diameter of 21.5 mm. The pipe is tightly secured to the wall at C. The couple shown is applied to the handles of the wrench. (Figure 1) Part A Determine the...
Learning Goal: To determine the maximum shear force that can be applied to two shafts of varying cross sections: a solid square shaft and a hollow square shaft. The two square cross sections shown below (Figure 1) are each subjected to a vertical shear force, V. The side length of each cross section is s = 6.00 in and the side length of the hollowed- out portion of the second cross section is r = 2.25 in. The maximum allowable...
Most questions answered within 3 hours.
-
1. What is the meaning of the term communication style?
2. What are the benefits to...
asked 3 minutes ago -
9.) You are buying a car that cost $26,500. You make payments of
$412 each month...
asked 28 minutes ago -
. Suppose a discrete random variable has probability
distribution
P(x) = .2 if x = 0...
asked 1 hour ago -
Problem #1
The area between Z = 0 and Z = 2.50
The area between Z...
asked 45 minutes ago -
Under the influence of its drive force, a snowmobile is moving
at a constant velocity along...
asked 2 hours ago -
Why do organizations decline? What steps can top
management take to halt, decline, and restore organizational...
asked 1 hour ago -
What mechanisms Drive speciation??
(I.e. what was Dawins theory on the orgin of species, and how...
asked 3 hours ago -
The manager at a car assembly plant believes that the mean
assembly time for a car...
asked 4 hours ago -
Which of the following is true of electron capture?
A) It decreases the nuclide's mass number...
asked 6 hours ago -
Assuming an efficiency of 43.10%, calculate the actual yield of
magnesium nitrate formed from 114.9 g...
asked 6 hours ago -
The highly pathogenic bacterium Clostridium
perfringens causes gangrene, a disease that results in the
destruction of...
asked 8 hours ago -
In the context of situation analysis, which of the following is
a category for analysis in...
asked 8 hours ago