Measurements and analysis of a circuit Lab!!
I need help finding Current 1, Current 2, Current 3. Please show the work!!
and also the last two questions
Measurements and analysis of a circuit Lab!! I need help finding Current 1, Current 2, Current...
In the circuit used to verify Kirchhoff’s current law, R2 and R3 are connected in parallel. a. Calculate the equivalent parallel resistance Rp using your measured values of R2 and R3. b. Your value of Rp, calculated above in part 2.a, is in series with R1. Calculate Rs using the measured value of R1 and your calculated value of Rp in part 2.a. c. Using the value of Rs from part 2.b above, and 5.00 volts, calculate the current. Call...
I don't need the measured values 1) Given the circuit in Figure 2 below, fill in Table 2 and 3 with the missing information. See the following Procedure B. N2 ETH V R2 VR4 Ref Node Figure 2 PS The blue power supply R1 120 ohms R2 220 ohms R3 330 ohms R330 ohms RL1000 ohm variable potentiometer Page 3
I am working on my Physics lab report where it was all about Direct Current Measurement and Ohm’s Law. We had 5 different resistors and had to construct different circuits using a power supply, volt-ohm-milliammeter (VOM) and a digital multimeter to get measurements of resistance, voltage, and current. Nominal values of resistance and tolerance Resistor Nominal Resistance (Ohms) Tolerance (Ohms) R1 680 +/- 68 R2 1000 +/- 50 R3 1500 +/- 75 R4 4700 +/- 470 R5 10,000 +/- 500...
Need help with conclusion questions please 1. The objectives of this lab are (1) to determine the actual (A) total resistance of three resistors connected in series and compare it with the experimental (E ) value of total resistance (2) to determine the actual (A) total resistance of three resistors connected in parallel and compare it with the experimental(E ) value of total resistance II. Apparatus(Equipment): Voltage source, ammeter that measures current , voltmeter that measures voltage. II. Procedure: Three...
Circuit#1: series-Parallel Circuit need help for questions 3,4,5,6 show answer please Phys 10071207 Lab Assignment #1 CIRCUIT #1. SERIES-PARALLELCIRCUIT Power supply setting (E): 15 Volts Ri: 10002 Rz: 25000 R3: 6252 Vi (meas)- 10, 35V V3 (meas) 1 (meas) = Series Parallel circuit R, 1. Find I2(calie) and I(calc) using/2ae) V mea) R andscatc) VsCes)/R 2. Calculate Requ 3. Using the given values of E and Requ, find ITot 4. Find the % Error between 11 and hot 5. Verify...
EE 282-Circuit I Pre-Lab 9 Maximum Power Transfer Theorem Name Concepts: In this pre-lab we will be leaming about Maximum Power Transfer Theorem. Maximum power is transferred to the load when the load resistance equals the thexenin equivalent, and we carry out the analysis using Thevenin's equivalent circuit. In order to do this, first build the following circuit on Mutism. 1 R1 5.1k0 R3 2 V1 R2 8kQ 6.8㏀ Fig. 1 Part 1: To find the Thevenin equivalent resistance, we...
I only need help with the discussion there are many info that you do not need put I put just in case as well as my data table. please do it as soon as u can Meauements ODeit1 Check2 Meaurements Checi3 Ced Check5 Check6 Measurements Check7 heck8 4058 33 536 1502 1035 979 119478 041 1.0319|0.554972| 64261| 153|15542033681 995781 5266566 1578807 298h 1631 119 1209430016 079096812 0.418135246 0,00032665 011890:004668155728441 0293237 1.291809502 1.22833 1.28 1952 -1116 4281 140616885511984206317 3346 8162 0.78...