3. For the regulated power supply shown in Figure 5-3, which is a full-wave bridge rectifier...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform and convert it to a “regulated “dc value giving 12 volts +, - 1 volt across a 2000-ohm output load resistor with no more than 2% ripple voltage. You may assume: a. An ideal power transformer as discussed in class. b. For hand computations, you must assume a diode given by Figure 4.8 page 185. c. A filter capacitor sized per the textbook equation...
3. Consider the full-wave bridge rectifier circuit shown below. The full-wave bridge is made using silicon diodes. 120V 15V 120 V(ms) n 60 Hz 752 Vout a. Find the maximum value of VoUT, and the voltage rating for the capacitor assuming a 50% margin of safety. b. Choose the capacitance of the filter capacitor for a peak-to-peak ripple of 1V, and determine the corresponding peak diode current. What is the frequency of the ripple voltage? c. Now suppose the filter...
It is required to use a FULL-wave rectifier to design a dc power supply that provides an average dc output voltage of 15 V. A maximum ripple voltage of ±1 V is allowed on the output voltage. The output voltage will feed a load resistance of 250 Ω. Assume a sinusoidal input voltage with the frequency of 60 Hz. Do not include a Zener diode in your design. (Assume V_D0)* = 0.7 V). a) Draw the circuit diagram. b) Calculate...
QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates from the mains and provides an output of Voc-20 V with 20% ripple, when the load current is 2 A Calculate the maximum and minimum values of the output waveform of this power supply. b. Now you will design a series voltage regulator between the power supply described in part (a) and an electronic device operating at 12 VDC...
Power Supply with Zener Voltage regulator D4 131 12 Vpk Vs 60 Hz 0° D2 D3 2. Simulate the bridge rectifier with three different filter capacitors(1uf, 5μF and 10μF) and observe output waveforms. Compare ripple voltages, estimation vs. simulation values Plot v, and vout waveforms. Power Supply with Zener Voltage regulator D4 131 12 Vpk Vs 60 Hz 0° D2 D3 2. Simulate the bridge rectifier with three different filter capacitors(1uf, 5μF and 10μF) and observe output waveforms. Compare ripple...
QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter It operates from the mains and provides an output of Voc-: 20 V with 20% ripple, when the load current is 2 A. Calculate the maximum and minimum values of the output waveform of this power supply. b. Now you will design a series voltage regulator between the power supply described in part (a) and an electronic device operating at 12...
6.26. Calculate the average power delivered to the load for the full-wave bridge rectifier circuit in Figure 6.9 if the diode is ideal, Vac is sinusoidal with a peak value of 170 V, and the load resistor has a value of 100 12. AC D4 -DC 4 +DC 4 D AC RL FIGURE 6.9 Full-wave bridge rectifier circuit.
We are doing a full wave bridge rectifier experiment and I am asked to make a lab report. In the conclusion section we are asked to answer questions that I don't really understand. The questions are posted below. I need help with the second through fourth bullet points. Thanks! 1.3.8 In your Summary and Conclusions section give a brief summary of the three experiments that were done. Answer the following questions in your Conclusion; Compare the measured versus simulated data...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a transformer which has a rms secondary voltage of 15.6V. The primary of the transformer is connected to a 50Hz, 230VRMS power supply. A 2700uF filter capacitor is used. A current of 1.5 Amp is drawn from the supply. (i) Sketch a schematic diagram of the setup. (ii) Calculate the mean de output voltage. Assume each power diode has a forward voltage drop of 1...