Q_in = 0.09 QC_out = 0.03 QE_out = 0.06 DeltaZ = 18 Please show all work...
Please help with the following matlab code and please show all
work. Thank you!
Viscous losses in a pipe are expressed in terms of a friction factor, f. It is important to know the frictional forces in pipe flow because they result in pressure loss which must be accounted for in the piping system. For turbulent low in pipes, the friction factor is caleulated using the Colebrook e/D 2.51 where e is the roughness height, D is the pipe diameter...
please show all work and label each graph with necessaey
peaks
*Road next Chapter hope & Lee chce DOUSWH - 10 - 2 2 Noring story student was converting cyclohexanol to cyclohexyl bromide by using one equivalent of um bromide in a large excess of concentrated sulfuric acid. The major product she recovered was 967 m .compound of formula CHao that gave the following spectra: 1PC NMR not cyclohexyl bromide, but a comp u t er 70 180 160 140...
Please show all work clearly with steps and formulas will rate
if done right!
1) A sieve analysis test revealed the following data for a soil sample. Mass of oven-dry specimen M 500 g Location Tested by Date Percent of Mass of Soil Retained on Mass Retained Percent Percent Retained Sieve Sieve Opening Each Sieve on Each Sieve ner No. 00-R 4.750 2.000 0.850 30 0.600 0.425 0.250 0.106 0.075 0 40.2 84.6 50.2 40.0 106.4 08.8 59.4 8.7 10...
Correct all answers in red. Please complete entire answer!
Ignore the answers with red you think are correct!
Problem 17-1A Comparing costs using ABC with the plantwide overhead rate LO P1, P3, A1, A2 The following data are for the two products produced by Tadros Company. Direct materials Direct labor hours Machine hours Batches Volume Engineering modifications Number of customers Market price Product A $15 per unit 0.5 DLH per unit 0.4 MH per unit 200 batches 16,000 units 14...
please show work for all sub parts
A combined cycle gas turbine / vapor power plant uses the turbine exhaust as the energy source for the boiler. Each power system uses a single turbine. The gas power system is modeled as an ideal air-standard Brayton cycle. The vapor power system is modeled as an ideal Rankine cycle. Given specific operating conditions determine the temperature and pressure at each state, the rate of heat transfer in the boiler, the power output...
Answer the questions using the data and graph. please show all
work. Thank you
Titration of Hydrochloric Acid: 1) Use the buret that is located near the hydrochloric acid container to dispense 25.00 mL of hydrochloric acid solution into a clean dry 100 mL beaker. Record the molarity of this solution on your data sheet. 2) Check to make sure that the volume on your sodium hydroxide buret reads 0.00 mL. If it does not read 0.00 mL, adjust it...
Water at 50 °Fis circulated from a large tank, through a filter, and back to the tank Calculate the volumetric flow rate through the filter for the following given information: Patm V.. Valve Pump Filter Pump power: W=200 lbf.ft/s Pump efficiency: 1p-0.9 Total pipe length: /= 200 ft Pipe diameter: d=0.1 ft Pipe surface relative roughness: /d=0.01 Elbow loss factor (each): Kelbow=1.5 Valve loss factor: Kvalve-6 Inlet and Exit type: sudden, Fig. 6.22 Filter loss factor Kriter=12 F (velocity, ft/s...
Please show work as well if you can, thank you.
. Appendix B Specimen Financial Statements: The Procter & Gamble Company Once each year, a corporation communicates to its stockholders and other interested parties by issuing a complete set of audited financial statements. The annual report, as this communication is called, summarizes the financial results of the company's operations for the year and its plans for the future. Many annual reports are attractive, multicolored, glossy public relations pieces, containing pictures...
solve no: 3.14 , 3.16, 3.19
please show each step and solve for beginners
120 Power System Analysis 3.12. A single-phase system similar to that shown in Figure 3.11 has two transformers A-B a B-C connected by a line B feeding a load at the receiving end C. The ratings and parame ter values of the components are 500 V/1.5 kV, 9.6 kVA. leakage reactance 5 % 1.2 kV/120 V, 7.2 kVA, leakage reactance 4 % series impedance (0.5 +...
Need help, numbers 3-6 please show work. and fill out table of
chemicals for all chemical used.
calculate mmol in the table as well show work please
and each of these must be listed in its own row. There are 10 column headings: IUPAC name OR common name, structure, CAS number (Chemical Abstract Service number) molecular mass, melting point (if applicable), boiling point (if applicable), solubility (in water, if applicable), density, amounts to be used in the experiment, and the...