A 60-m-long steel wire is subjected to a 6.5-kN tensile load. It is given that E...

Question

Question

A 60-m-long steel wire is subjected to a 6.5-kN tensile load. It is given that E = 200 GPa and the length of the rod increases by 48 mm.

Determine the smallest diameter that can be selected for the wire.

Answer 1

Answer #1

Corendala 6.skN 7 60m 60m เรจ ว า ะ เรา E = 200 GPa 6.SINI U AE when lngth a nuod increasing than equation giren by Carral) S

Answer 2

Similar Homework Help Questions

1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m...

1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. What is the Poisson's Ratio of this material? 2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length...
A 25mm diameter steel rod 1.5m long is being used in a rigid structure. For this...

A 25mm diameter steel rod 1.5m long is being used in a rigid structure. For this steel the Ultimate Tensile Stress is 410 MPa Young’s Modulus is 200 GPa The rod is to be subjected to a tension load of 40 kN. Design requirements are that the rod cannot extend by more than 0.5 mm and that there is a Factor of Safety of 5 for the tensile stress. Determine whether or not the rod is adequate for the task:...
A tensile force of 120 kN is applied on a 0.02-m diameter and 2-m long rod....

A tensile force of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The engineering stress on that rod is most nearly: PLEASE SHOW ALL WORK. A tensile force of 120 leN is applied on a 0.02-m diameter and 2-mm long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the...

The concrete [E = 29 GPa] pier shown in the figure is reinforced by four steel...

The concrete [E = 29 GPa] pier shown in the figure is reinforced by four steel [E = 200 GPa] reinforcing rods, each having a diameter of 19 mm. Assume P = 680 kN, L = 2.10 m, and a = 275 mm. If the pier is subjected to an axial load of 680 kN, determine (a) the normal stress (positive if tensile and negative if compressive) in the concrete and in the steel reinforcing rods. (b) the deflection of...
A P=2-kN tensile load is applied to a test coupon made from 1.6-mm thick flat steel...

A P=2-kN tensile load is applied to a test coupon made from 1.6-mm thick flat steel plate (E = 220 GPa, v = 0.30). Assuming a=45 mm and b=13 mm, (a) Determine the resulting change in the 45-mm gage length. (b) Determine the resulting change in the 13-mm width. (c) Determine the resulting change in the 1.6-mm thickness. (d) Determine the resulting change in the cross-sectional area. The uniaxial state of stress in given as ________ (MPa) A P-2-kN tensile...
A 100-mm long rod has a diameter of 15 mm, Part A If an axial tensile...

A 100-mm long rod has a diameter of 15 mm, Part A If an axial tensile load of 195 kN s applied, determine its change in length. Assume linear-elastic behavior with E = 200 GPa. Express your ahswer to three significant figures and include the appropriate units. ? Suomi Request Answer Provide Feedback

P-580 kN Problem 2 Rod BD is made of steel (E 200 GPa) and is used...

P-580 kN Problem 2 Rod BD is made of steel (E 200 GPa) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 124 MPa and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD 1.8 m 1.8 m 1.35 m
Q} A mild Steel rod of 10 mm dia., 25 mm long was subjected to a...

Q} A mild Steel rod of 10 mm dia., 25 mm long was subjected to a tensile load of 5 kN, its elongation been 0.277 mm, estimate the value of its young's modulus
Q2 The 10 m long simply supported beam is subjected to a uniformly distributed load w...

Q2 The 10 m long simply supported beam is subjected to a uniformly distributed load w = 10 kN/m throughout and a point load P =10 kN at the midspan of the beam, as shown in Figure Q2 (a). The cross section of this beam is depicted in Figure Q2 (b), which consists of three equal rectangular steel members. Self-weight of the beam is neglected. 30 mm P= 10 KN W = 10 kN/m 200 mm 5 m 5 m...

Q2 The 10 m long simply supported beam is subjected to a uniformly distributed load w...

Q2 The 10 m long simply supported beam is subjected to a uniformly distributed load w = 10 kN/m throughout and a point load P =10 kN at the midspan of the beam, as shown in Figure Q2 (a). The cross section of this beam is depicted in Figure Q2 (b), which consists of three equal rectangular steel members. Self-weight of the beam is neglected. 30 mm P = 10 kN W = 10 kN/m 200 mm 5 m 5...