We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
a. Consider the following signal xi(t)= cos(2aft) The signal is sampled with the sampling frequency Fs....
Consider a sampler which samples the continuous-time input signal x(t) at a sampling frequency fs = 8000 Hz and produces at its output a sampled discrete-time signal x$(t) = x(nTs), where To = 1/fs is the sampling period. If the sampled signal is passed through a unity-gain lowpass filter with cutoff frequency of fs/2, sketch the magnitude spectrum of the resulting signal for the following input signals: (a) x(t) = cos(6000nt). (b) x(t) = cos(12000nt). (c) x(t) = cos(18000nt).
MATLAB Fourier transform. Suppose that a signal x(t) is sampled with sampling frequency fs =100Hz. The sequence x[n] obtained after the sampling is given below: Take the DFT of the sampled sequence and plot its magnitude and phase. What is the frequency resolution (Δf) of your plot? N= 20, 100 Hz N= 20, 100 Hz
The signal x(t) 10 cos(2t (3300) t +0.2x)) is sampled at fs 8 kHz (a) Determine the sampled signal x[n]. (b) What would be the lowest possible sampling frequency for reconstructing x(0)? 4.
Plot the signal s(t) = cos(2πt), and then illustrate the resulting samples with the following sampling intervals: [30 points] • Ts= 0.5 sec. • Ts= 0.75 sec • Ts =1 sec. (a) For each case, also sketch the reconstructed continuous time signal from the samples using linear interpolation (i.e. connecting samples by straight lines). (b) In which case the sampled signal has aliasing distortion? What is the minimal sampling frequency and the corresponding sampling interval needed to avoid aliasing? 3....
1. A signal, x(t) = 2 cos(21fmt), is applied to the ideal sampling circuit in the Figure below (left) where fm = 1 kHz. A sampling function, p(t), whose characteristic is given in the Figure below (right), is used when Ts = 0.25 ms. a) (5p) Plot the sampled signal, xs(t), in time domain for at least one period. b) [10p] Express the Fourier transform of sampled signal, xs(t), denoted by Xs , in frequency domain. c) [10p] Plot the...
. Problem 1: The signal r(t) = 2 cos(27300t) + cos(27 400t) is sampled with sampling frequencies a) 2. = 20007 and b) 2. = 15007. 1) Sketch the amplitude spectra of the sampled signal r(t) in both cases. 2) Sketch the output of the ideal low pass filter with a cut-off frequency 1000m in both cases.
36. Sampling a low-pass signal. A signal x(t) = sin( 1,000.71) is sampled at the rate of F, and sent through a unity-gain ideal low-pass filter with the cutoff frequency at F,/2. Find and plot the Fourier transform of the reconstructed signal z(t) at filter's output if a. F=20 kHz b. Fs =800 Hz
10. Find the Fourier transform of a continuous-time signal x(t) = 10e Su(t). Plot the magnitude spectrum and the phase spectrum. If the signal is going to be sampled, what should be the minimum sampling frequency so that the aliasing error is less than 0.1 % of the maximum original magnitude at half the sampling frequency. 11. A signal x(t) = 5cos(2nt + 1/6) is sampled at every 0.2 seconds. Find the sequence obtained over the interval 0 st 3...
3. (50 points] Consider the signal (t= cos(27 (100)+]: 1) Let's take samples of x(t) at a sampling rate fs = 180 Hz. Sketch the spectrum X (f) of the sampled signal x (t). Properly label x-axis and y-axis. 2) Now suppose we will use an ideal lowpass filter of gain 1/fs with a cutoff frequency 90 Hz for the sampled signal xs(t). What is the output of the filter x,(t)? 3) Now let's take samples of x(t) at sampling...
Problem 3: Sampling a Cosine (again) The continuous-time signal ra(t) = cos (150) is sampled with sampling period T, to obtain a discrete-time signal x[n] = XanT). 1. Compute and sketch the magnitude of the continuous-time Fourier transform of ra(t) and the discrete-time Fourier Transform of x[n] for T, = 1 ms and T, = 2 ms. 2. What is the maximum sampling period Ts max such that no aliasing occurs in the sampling process?