Problem 3: Sampling a Cosine (again) The continuous-time signal ra(t) = cos (150) is sampled with...
3. The signal continuous time signal re(t)-cos(200t)2cos cos(100t) is sampled at twice the Nyquist rate to get the sequence r[n]. (a) Sketch X(e) (b) If y[n] = [4n]. Sketch Y(e'"). (c) Is there any aliasing in the Fourier spectrum of yin]? Why or Why Not? (d) If z [n] = x-1, ketch the DTFT of z[n] (e) Is there any aliasing in the Fourier spectrum of [n]? Why or Why Not? 3. The signal continuous time signal re(t)-cos(200t)2cos cos(100t) is...
10. Find the Fourier transform of a continuous-time signal x(t) = 10e Su(t). Plot the magnitude spectrum and the phase spectrum. If the signal is going to be sampled, what should be the minimum sampling frequency so that the aliasing error is less than 0.1 % of the maximum original magnitude at half the sampling frequency. 11. A signal x(t) = 5cos(2nt + 1/6) is sampled at every 0.2 seconds. Find the sequence obtained over the interval 0 st 3...
(a) The continuous-time signal x(t) with FT as depicted in the figure shown below is sampled. Sketch the FT of the sampled signal for the following sampling intervals: identify whether aliasing occurs, Ts = 1/12 X(jw) -117 107 W -10 0 117 97 97T (b) Determine the z-transform and ROC for the following time signals: x[n] = (4)"u[n] + (1)"u[ -– 1] Sketch the ROC, poles, and zeros in the z-plane.
Q2.) Consider the sampling of the continuous-time signal x(t) to obtain a discrete-time signal x[n (1)-10cos(1000m + π/3) + 20cos(2000m + π/6). 110points! ], where x a) What is the maximum sampling interval (minimum sampling frequency) that could be used to ensure an aliasing free sampling of this signal? b) Plot the spectrum of the sampled signal if x() is sampled using a sampling frequency of (i) 2500 Hz (ii) 1800 Hz and state whether there will be an aliasing...
Consider the continuous time signal: 2. , π (sin (2t) (Sin (8t) A discrete time signal x[n] -xs(t) -x(nTs) is created by sampling x() with sampling interval, 2it 60 a) Plot the Fourier Transform of the sampled signal, i.e. Xs (jo). b) Plot the DTFT of the sampled signal, ie, X(eja) o) Repeat (a) with 7, 2π d) Repeat (b) with , 18 Consider the continuous time signal: 2. , π (sin (2t) (Sin (8t) A discrete time signal x[n]...
Consider a sampler which samples the continuous-time input signal x(t) at a sampling frequency fs = 8000 Hz and produces at its output a sampled discrete-time signal x$(t) = x(nTs), where To = 1/fs is the sampling period. If the sampled signal is passed through a unity-gain lowpass filter with cutoff frequency of fs/2, sketch the magnitude spectrum of the resulting signal for the following input signals: (a) x(t) = cos(6000nt). (b) x(t) = cos(12000nt). (c) x(t) = cos(18000nt).
(1) Consider the following continuous-time signal: (1) 2ua(-t+t)ua(t), where its energy is 20 milli Joules (2 x 103Joules). The signal ra(t) is sampled at a rate of 500 samples/sec to yield its discrete-time counter part (n) (a) Find ti, and hence sketch ra(t). (b) From part (a), plot r(n) and finds its energy (c) Derive an expression for the Fourier transform of a(n), namely X(ew). (d) Plot the magnitude spectrum (1X(e)) and phase spectrum 2(X(e). (e) Consider the signal y(n)...
Q. 2 A continuous time signal x(t) has the Continuous Time Fourier Transform shown in Fig 2. Xc() -80007 0 80001 2 (rad/s) Fig 2 According to the sampling theorem, find the maximum allowable sampling period T for this signal. Also plot the Fourier Transforms of the sampled signal X:(j) and X(elo). Label the resulting signals appropriately (both in frequency and amplitude axis). Assuming that the sampling period is increased 1.2 times, what is the new sampling frequency 2? What...
Plot the signal s(t) = cos(2πt), and then illustrate the resulting samples with the following sampling intervals: [30 points] • Ts= 0.5 sec. • Ts= 0.75 sec • Ts =1 sec. (a) For each case, also sketch the reconstructed continuous time signal from the samples using linear interpolation (i.e. connecting samples by straight lines). (b) In which case the sampled signal has aliasing distortion? What is the minimal sampling frequency and the corresponding sampling interval needed to avoid aliasing? 3....
10ρ 18ρ A signal (t) has the Fourier transform X(jw) indicated in the figure. The signal is sampled to obtain the discrete time signal 1. Sketch the Fourier transform Xr(jw) of x[n] for T-to. 2. Can x(t) be recovered for T? How? What is the maximum value of T so that r(t) can be recovered? 10ρ 18ρ A signal (t) has the Fourier transform X(jw) indicated in the figure. The signal is sampled to obtain the discrete time signal 1....