Q3. For the circuit shown, specify values of Vx and Rx that cause the output voltage V0 and the input voltage Vs to have the relationship specified by the graph shown.
Q3. For the circuit shown, specify values of vx and R that cause the output voltage...
The circuit shown has four unspecified circuit parameters: vs. R1, R2, and d, where d is the gain of the CCCS. To design this circuit, we must specify the values of these four parameters. The graph shown describes a relationship between the current i and the voltage v. Specify values of vs. Ri, R2, and d that cause the current i and the voltage y to satisfy the relationship described by the graph. Hint: The equation representing the output voltage...
1. Find the ratio of the output voltage to the input voltage, Vo/Vin, in the circuit shown. State your assumptions in using the ideal op-amp model. 15 k2 Vin 2. Find the output voltage Vo in the circuit shown assuming an ideal op-amp. State your assumptions in using the ideal op-amp model 15 k12 Vo . Find the voltage Vx and the output voltage Vo in the circuit shown assuming ideal op-amp 3 k2 1 V 6 kn 12 k2
A signal source with an open-circuit voltage of Vs = 2 mV rms and an internal resistance of 50 kΩ is connected to the input terminals of an amplifier having an open-circuit voltage gain of 100, an input resistance of 135 kΩ , and an output resistance of 4 Ω. A 4 Ω load is connected to the output terminals. Find Voltage gain Avs = V0/Vs Find voltage gain Av = V0/Vi Find current gain Ai Find power gain G...
17.6 Derive the relationship between the output, the potential difference across the resistor R of vx, and the input v for the series LCR circuit shown in Figure 17.23. Figure 17.23 Problem 17.6.
Determine the values of R1, R2, and Vx such that VTH = 6V and VTL = 4V (consider the voltage of saturation +,-Vsat = +,-15V). Once the above is done, determine the graph of the output voltage considering the input signal Vi shown below 10 Vi 6 Vo R2 R1 t, S
The circuit to the left is constructed with a 1kS2 resistor and a 1 mF capacitor. The input waveform is shown below. A) Sketch a graph of the output voltage for this graph, starting at t 0 and ending it once the capacitor has Rreturned to an apparent steady state. Be sure to label rtant points and values ts the value of output voltage at t-11 seconds? 12 seconds? C) Sketch a graph of the output current for this graph,...
Question 2 (10%) The input to the circuit shown in Fig. 2 is the voltage source vs(t). The output is the voltage across two open terminals, vo(). If v()-3-(t) V, the output is the voltage vo()-10+Se30* V for 20. Determine the values of Ri and R2. 2 sa) olt) Fig. 2
Q2A) In the single current source circuit shown in the below fig., find the voltage Vx. Interchange the current and voltage Vx. Is the Reciprocity theorem verified? [6 Mark] 5190°A 3502 3202 350g -j2 12 - Vx 1
or the following circuit, sketch the output voltage, given an input voltage waveform as shown on the axes below. Assume a constant voltage drop diode model with Vo- 0.7. +15.0V 4 1mA OVout 3009 3 Vo -4 0 0.2 0.4 0.6 0.8 in or the following circuit, sketch the output voltage, given an input voltage waveform as shown on the axes below. Assume a constant voltage drop diode model with Vo- 0.7. +15.0V 4 1mA OVout 3009 3 Vo -4...
In the circuit shown in Figure P5 (a). Determine an expression for the output voltage (b). Assume si .910 cos(or)+v,). vs 3.1x10cos(v,(), S2 ouut determine the numerical value of, the output voltage. Figure P5.