Q) In forging operation, does the power requirement decrease in the final steps? (Yes or No)...
6 Sp19 ().pdf 3/Downloads/Hw6.Sp 19%20(1).pdf In the process of manufacturing a steel forging, answer the following questions: i. During melting, what two principal impurities are introduced into the melt pool when the i. How are these removed from the melt pool in subsequent processing? (Hint: the methods ii. During ingot manufacture, which primary steel alloying element segregates with a low ladle is tapped through the open atmosphere? are different for each) concentration at the bottom and a high concentration at...
pls show steps on how to, thanks!
Does the function satisfy the hypotheses of the mean value theorem on the given interval? Give reasons for your answer. X - X f(x) = - 2 5x51 1<x54 2x2 - 3x + 1 Choose the correct answer. O A. No, f(x) is continuous at every point in (-2,4] but is not differentiable at every point in (-2,4), O B. No, f(x) is differentiable at every point in (-2,4) but is not continuous...
Difference in final temperatures? Please show all steps
Two containers (call them A and B) with the same initial volume, V 31 L, hold the same amount of monatomic ideal gas, say helium, at the same initial temperature T = 301 K and the same initial pressure Pi 1 atm. Container A holds the gas at a constant volume and Container B holds the gas at a constant pressure If you add Q 5389 J of heat to both containers,...
Your response: Do not round intermediate calculations, however for display purposes report intermediate steps rounded to four significant figures. Give your final answer(s) to three significant figures. Enter tension forces values as positive numbers and compression forces values as negative numbers 16 ft 7 ft 7 ft 4 ft 3.0 kip 3.0 kip 14 ft 6.6 kip 14 ft D E 4 ft 4 ft The electric power transmission tower supports two wires that apply 3.0-kip, vertical forces, and the...
i-1i0 (Two Choices: (a) or (b)) 1. One may decrease the power of a hypothesis test by increasing the sample size n. True (b) False 2, The Central Limit Theorem even applies to a sample meany from a population with a uniform distribution. (a) True (b) False 3. If events A, B, and Care all mutually-independent, then P(A u B u C) P(A) + P(B) + P(C (a) True (b) False 4. For any data set, at least half of...
QUESTIONS Question-3: Draw "speed vs. torque" curve using data in Table-1. The completed graph represents the speed vs. torque characteristics of a typical DC shunt-wound motor. Terax Question-4: Calculate the speed regulation (full load - 12 lbf.in) using the equation: 2-143) 143 (no load Regulation (full load speed) Speed regulation- % Part-II - Motor Efficiency Calculation: Set the dynamometer control knob at its full CW position (to provide the maximum starting load for the shunt-wound motor). Turn on the power...
Please help with completing lab with the following measurements.
Thank you.
Final Temperature of water is 28 C
Mass (9) Water 200 Metal Ball 60 Initial Temperature (°C) Final Temperature (°C) 21 81 21 cusing T-1 cusing T cusing T+1 Lab 9: Specific Heat In this lab, you will measure the specific heat of the metal ball in your kit. To do this, you will heat it up to nearly 100°C and then submerge it in room temperature water. After...
please show steps and how to so I can understand :)
IST FURT ULU) Mohanad Alsunbul 02/03/20 8:31 PM Homework: Chapter 3 Homework (required) Save 5 of 9 (8 complete) HW Score: 86.52%, 7.79 of 9 pts Score: 0 of 1 pt E3-22A (similar to) Question Help od Lincoln Plastics manufactures custom park furniture and signage from recycled plastics (primarily shredded milk jugs) Many of the company's customers are municipalities that are required by law to purchase goods that meet...
solve no: 3.14 , 3.16, 3.19
please show each step and solve for beginners
120 Power System Analysis 3.12. A single-phase system similar to that shown in Figure 3.11 has two transformers A-B a B-C connected by a line B feeding a load at the receiving end C. The ratings and parame ter values of the components are 500 V/1.5 kV, 9.6 kVA. leakage reactance 5 % 1.2 kV/120 V, 7.2 kVA, leakage reactance 4 % series impedance (0.5 +...
Give an specific example and describe the operation of a perpetual motion machine. Will the machine work? Why or why not? Reply to the posts of at least two other students as well as comments on your own post. 13 Use the Everyday Phenomenon Box 11.2 on page 230 of the textbook as an example. Do not post this as your example, however. Everyday Phenomenon Box 11.2 Water turbine O n A Productive Pond The Situation. A local farmer consulted...