Is1 15 mA R. 1ΚΩ In the circuit shown, use KCL, KVL, and Ohm's Law to...

Question

Question

Is1 15 mA R. 1ΚΩ In the circuit shown, use KCL, KVL, and Ohms Law to find the two resistor currents R1 R2 K. S2 25 V 0.5 kΩ 5 mA iR2 1R2 =

Answer 1

Answer #1

9 SMA SMA at node at Ned토0 (kCL 0k Ndi@) 1に R, r AJ .3le

Answer 2

Similar Homework Help Questions

From the circuit shown below, (a) use KCL and KVL to solve for the three currents....

From the circuit shown below, (a) use KCL and KVL to solve for the three currents. (b) With the given data below and the two currents flowing clockwise, determine both currents using mesh analysis and the voltages across each resistor. r1= 3 Ohms r2= 7 Ohms r3= 2 Ohms r4= 8 Ohms a M 10 V 30 il 222 i2 722 892 i3 12 V W
Pre-lab EM-5 Ohm's Law and Kirchhoff's Rules Ohm's Law The resistance R of a device can...

Pre-lab EM-5 Ohm's Law and Kirchhoff's Rules Ohm's Law The resistance R of a device can be determined by either directly measuring the resistance using an ohmmeter, or by measuring the current I through it and the voltage Vacross it, and then calculating R using Ohm's Law V R= (1) If the voltage across a resistor is 10V, and the current passing through it is 2.5 mA. of the resistor? What is the resistance R= Ω. Kirchhoffs Loop Rule Around...
3-3: Use KVL/KCL and Ohm's Law as needed to find the values of v1 and v2....

3-3: Use KVL/KCL and Ohm's Law as needed to find the values of v1 and v2. You must show separate KCL and KVL equations, no credit will be given if other methods such as nodal analysis are used. 80 80 Ω υ,Σ 120 Ω V140 6 A

4. Find in the circuit below if V = 4/0° VAMS- Note: use KVL, KCL, and...

4. Find in the circuit below if V = 4/0° VAMS- Note: use KVL, KCL, and Ohm's Law to solve. {0.52 WM 5. Determine the average power and complex power supplied by the source, V , in problem 4.
Apply the following questions to both the circuit shown in Figure (a) (resistors in series) and...

Apply the following questions to both the circuit shown in Figure (a) (resistors in series) and the circuit shown in Figure (b) (resistors in parallel). (a) Use Ohm's law with Kirchhoff's current and voltage laws to derive equations for currents i1, i2 and i (through Resistor R1, resistor R2, and the voltage source , respectively) in terms of R1, R2, and v. (b) R1 and R2 can be interchanged with an equivalent resistor rith resistance R without changing the values...
PI : For circuit below v-20 V and R,-8 Ohm and R2-2 Ohm. Calculate voltage and...

PI : For circuit below v-20 V and R,-8 Ohm and R2-2 Ohm. Calculate voltage and power loss in each resistor in the circuit. (Use voltage division and P = (voltage*voltage) resistance)- You cannot use KVL, KCL or Ohms law) Ri R2 P2: For circuit below i = 50 A and R1 = 15 Ohm and R2 = 10 Ohm. Calculate current and power loss in each resistor in the circuit. (Use current division and P - (current*current) resistance) You...

find volatges and currents across all resistors using ohms law , kcl, and kvl. Rl R2...

find volatges and currents across all resistors using ohms law , kcl, and kvl. Rl R2 1.5 kJ2 R3 는 2kl2 Rt J1 12 inl voltage anol current throush all resistors R1, R2, R3, R4 in Voltage ah no
For the circuit shown below, using Ohm's law enter in an equation for IR1, IR2, IR3...

For the circuit shown below, using Ohm's law enter in an equation for IR1, IR2, IR3 IR4, IR5, and IR6,in terms of the voltage at nodes 1, (V1),2, (V2), 3, (V3), 4, (V4), R1, R2, R3, R4, R5, Rf6 A sample answer would be (V1-V2)yR1. If you are getting a syntax error, you might not be typing in the variables correctly. Do not try to add subscripts or any formatting, this will cause a syntax error as well. R1 R1...
In this circuit, the source voltage is VS = 25 V, and the resistances are: R1...

In this circuit, the source voltage is VS = 25 V, and the resistances are: R1 = 10 kΩ, R2 = 18 kΩ, R3 = 2 kΩ, R4 = 20 kΩ. Using the mesh current method, find the mesh currents Ia and Ib (polarities as marked). In this circuit, the source voltage is Vs = 25 V, and the resistances are: R1 = 10 k 2, R2 = 18 k22, R3 = 2 k.22, R4 = 20 k 2. Using...

Fig. 1. Logic circuit for Question 1 2. The 60 W light bulb shown in Fig....

Fig. 1. Logic circuit for Question 1 2. The 60 W light bulb shown in Fig. 2 is rated at 120 volts. Calculate the required supply voltage V, to make the light bulb operate at the rated conditions. (2 pts) 50 22 Bulb 3 802 Fig.2. Circuit for Question 2 (3 pts) 3. For the circuit shown in Fig. 3, using KVL & KCL: a. Determine the currents i1, 12 & 13 b. The voltage across the resistor R1, R2...