This is a very interesting problem that i cant figure out. please answer the question clearly and show all work.
Thanks!
This is a very interesting problem that i cant figure out. please answer the question clearly...
I need a full solution for those questions please, although I'm half way through question one and it is quite simple but I would like to double check if Ive got that right. like and comment are rewarded for good answers Consider the following circuit containing a switch S, an ideal battery with e.m.f. ε-20.0 V, resistors R,-: 8.00 Ω, R2-20.0 Ω and R3-30.0 Ω, and capacitors R2-20Ω RI-8Ω R3 -3082 After the switch is closed: (a) Calculate the initial...
Group Problem 2: You are given the task to determine the inductance M of two inductors of unknown self-inductances L1 and L2. Recall that M = M12 = M21 and the magnetic flux B1,2 = M12/1 and B2,1 = M2112. To perform this task, you connect one of the inductors (say L1) in series with a battery of emf = 10 V and a resistor of resistance R1 = 212. These three components, as well as a switch S, form...
2) Shown below is a c R2 = 7 Ω, R3 = 24 Ω, R4 = 10 ircuit with two switches. Si and S2M = 15 V, V.-5 V, V,-20 V, Rı = 15 Ω . 25s2 C,200F v -,,I -R, Г 2:0 start atp sition A. This creates two dependent circuits. The left circuit with only resistors '5 V-15A)(T)-YAG).2ov-ocharges the capacitor C, through resistor Rs with battery Vs(the capacitor is initially The switch 1 will start in the on/closed...
Read before answering Please and please, make sure you attempts all of the problems and clearly explain the steps to each problems....Make sure your answer is 100% correct before posting it RC Circuits Optional Two Loop RC Circuit 1 1 23 4 56 Inceractive txample 3r2c A circuit is constructed with four resistors, one capacitor, one battery and a switch as shown. The values for the resistors are: R1·R2·75 Ω,R,- 104 Ω and R4-81 Ω. The capacitance is C-60 and...
Needs to be answered urgently (about 45minute) In the circuit shown in figure, switch S1 is closed and switch S2 is left open. After a long time the current in the circuit has reached its final, steady value. Then, while S1 is kept closed, switch S2 is closed (thus short-circuiting the inductor). Just after S2 is closed, what is the current through R2? R, = 222 w R2 = 322 Si S2 0000 L=1 H E = 50 V +...
Question 21 No Initial energy in Inductor. V 480 Volts. Switch S has been open for long. R1 R2 R3- R4 R5 80 Ohms. Inductance L-4 H enries. Switch S closed at timet-0. .a) What are values of current Is through Switch, and current lIL current IR1 through R1, and voltage VL across inductance atto-, just before the switch is closed? R1 R3 It Is R2 . at (t0- Is... IL R. Vu .b) What are the values of IS,...
Question 16 Not yet answered Points out of 6.00 Prag question In the circuit below R1 = 7.50, R2 = R3-50, and L = 31 mH. The battery supplies 12 V. R R -8 RO lle (a) What is the current through the battery right after the switch is closed? Select one: O a. 1.60 A O b. 0.96 A O c. 0.00 A O d. 1.20 A O e. 0.53 A Tube Maps In the circuit below R1 =...
(3) The RL circuit shown in Figure 3 has a switch that is closed att 0. Assume that the circuit has reached steady state prior to the switch closing. You are given R1 1 kQ, R2-10 kQ, R3-R4-100 k2, L 10 mH, Vs-5 V. (a) [15 pts] Calculate the steady-state inductor current before the switch is closed (b) [16 pts] Give the differential equation as an expression of the inductor current fort>0 (i.e. write the differential equation) (c) 13 pts]...
A common demonstration of inductance employs a circuit such as the one shown in the figure (Figure 1) . Switch S is closed, and the light bulb (represented by resistance R1) just barely glows. After a period of time, switch S is opened, and the bulb lights up brightly for a short period of time. To understand this effect, think of an inductor as a device that imparts an "inertia" to the current, preventing a discontinuous change in the current...
PRELAB: 1. From the data sheets, find the expected B of the transistors 2SC3067 and 2N3906 when Ic 2mA and the expected r, of the 2N3906 when Ic = 2mA 2. Using the current source model below Let Li be the current through RL1 Find an Connect a resistor Ri across the output terminals expression for Iui in terms of the current Is and the resistances in the circut Replace Ru1 with Ra: (a different resistor). Find an expression for...