Question

Question 2. Determine the work done in lifting a 100 kg block vertically 500 cm. Question 3. A gas engine supplies a torque oanswer both

0 0
Add a comment Improve this question Transcribed image text
Answer #1

- * solution - 100 kg block 2) Work Done in lifting verbcally 500 cm. - 500cm = 5m ab Now, Hook Done = Force a linear Displac

Note - Work done in lifting the block restically cpword is equal to potential energy W = PE = mgh 8.2) Shaft work done by eng

Add a comment
Know the answer?
Add Answer to:
answer both Question 2. Determine the work done in lifting a 100 kg block vertically 500...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • Question 3 1 points Save Answer A 2.0 kg object falls vertically downward in a viscous...

    Question 3 1 points Save Answer A 2.0 kg object falls vertically downward in a viscous medium at a constant speed of 2.5 m/s. How much work is done by the force the viscous medium exerts on the object as it falls 80 cm? +1.65) 15.7) -1.65) -15.7) +31.4)

  • What is the total work Wos done on the block by the force of riction as...

    What is the total work Wos done on the block by the force of riction as the block moves a dstance8 00 m up the ncine? Express the work done by friction numerically, in Joules Constants A block of mass 1.00 kg sts on an inclined plane as shown igure 1A force of magntude 100 N is puing the block up the nclne The coefficient of kinebc friction between the plane and the block is 0500 The inclined plane makes...

  • Please work out 3 clearly and with units. Thanks! 1. A 10-g bullet travels vertically upwards...

    Please work out 3 clearly and with units. Thanks! 1. A 10-g bullet travels vertically upwards at 1000 m/s, then strikes and passes through a 2.0-kg block initially at rest. The bullet emerges from the block with a speed of 400 m/s because it transfers momentum to the block. (a) How much momentum did the block gain? (b) How fast is the block now moving, and what is its kinetic energy? (c) Using energy considerations only, to what maximum height...

  • Calculate the Amount of Work Done to Lift an Object and Cable Question We use a...

    Calculate the Amount of Work Done to Lift an Object and Cable Question We use a rope with a linear mass density of 20 kg/m to lift a block of cement weighing 1000 kg 50 meters above the ground. The rope is 75 meters long but we need an additional 100 meters to secure the concrete block so it can be lifted safely. Find the total amount of work done (in kilojoules, remembering that (1 kJ = 1000 J). Do...

  • please answer both?!? Question 5 1 pts A block of mass 1.9 kg is placed on...

    please answer both?!? Question 5 1 pts A block of mass 1.9 kg is placed on a frictionless table with one of its ends connected to a spring. Initially, the spring is at the equilibrium. A force is applied to the block that slowly increases to reach the maximum value of 9 newtons. The block ends up 9.9 cm from the equilibrium. What will be the frequency of oscillations (in Hz) when the block is released? Question 6 1 pts...

  • ANSWER IS 0.8KN SHOW ALL WORK PLEASE!!!!! A 100-kg block is pushed up a 30° incline...

    ANSWER IS 0.8KN SHOW ALL WORK PLEASE!!!!! A 100-kg block is pushed up a 30° incline that is 10 m long. If the coefficient of friction between the block and the incline is 0.1, the constant force parallel to the incline that is required to move the block from rest at the bottom of the incline to the top in 3 s is approximately

  • shown in Figure 2. Two circular disks A and B are welded to the ends of both bars. The disks lie in planes disks A a...

    shown in Figure 2. Two circular disks A and B are welded to the ends of both bars. The disks lie in planes disks A and B subjecting the bars to torsion. If the allowable maximum shear stress is 35 MPa and the allowable rate of twist is 3°/m for both bars, determine the smallest outer diameter (D, and Di) of both bars. The shear modulus of elasticity is 39 GPa to the axes of the bars. Forces 15 kN...

  • just question number 2 please, hate my teacher for all the a b c d e...

    just question number 2 please, hate my teacher for all the a b c d e f g h..... s in the sink at a height of 1.00 meters above the floor. Ignoring friction in the hose, find b. The velocity of the water in the hose. d of a hose is subicl pressure in the hose at the highest point. 2. For the PV find the fol iagram shown to the right for a monoatomic gas, POPa) e follow...

  • Determine the work done by you in the following situations. A) Pulling horizontally with a force...

    Determine the work done by you in the following situations. A) Pulling horizontally with a force of 20 N on a 100 N sled. Sled moves 2 m at a constant velocity. (include units with answer) B) Pulling horizontally with a force of 40 N on a 100 N sled. Sled moves 2 m at a constant acceleration. (include units with answer) C) Pushing at 30° from horizontal with a force of 40 N on a 100 N sled. Sled...

  • please answer question 3 and 4. l bect is pushed across a surface with a coefficient...

    please answer question 3 and 4. l bect is pushed across a surface with a coefficient of kinetic friction between object and surface of 27. If the object slid with a speed of 3 how far will it go before it comes to rest? 3 A 4.2 kg car is lifted 25 m vertically with an acceleration a 265g by a single cable. Determine the net work done on the load. A box of mass 6.0 kg accelerates from rest...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT